INSIDE HANDLE LIGHT > INSTALLATION |
| 1. INSTALL FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY (for Front Door) |
Engage the claw and 3 clamps, and install the front door inside handle illumination light assembly.
| 2. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP (for Front Door) |
![]() |
Install the front door inner glass weatherstrip.
| 3. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY (for Front Door) |
![]() |
Engage the 2 claws and guide, and install the front door inside handle sub-assembly to the front door trim board sub-assembly.
| 4. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Front Door) |
![]() |
Connect the front door lock remote control cable assembly and front door inside locking cable assembly.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
Connect the connector.
![]() |
Engage the front door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
| *1 | Reference Boss |
![]() |
Engage the 10 clips and install the front door trim board sub-assembly.
Install the 3 screws.
If protective tape has been applied, remove it.
| 5. INSTALL COURTESY LIGHT ASSEMBLY (for Front Door) |
Connect the connector.
![]() |
Engage the claw to install the courtesy light assembly.
| *A | for LH Side |
| *B | for RH Side |
| 6. INSTALL FRONT ARMREST ASSEMBLY (for Front Door) |
![]() |
Engage the 2 guides, 3 clips and 7 claws, and install the front armrest assembly.
| 7. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Door) |
| 8. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Door) |
| 9. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH (for Front Door) |
![]() |
Engage the 3 clips to install the front door lower frame bracket garnish.
| 10. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG (for Front Door) |
![]() |
Engage the 3 claws to install the front door inside handle bezel plug.
| 11. INSTALL REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY (for Rear Door) |
Engage the claw and 3 clamps, and install the rear door inside handle illumination light assembly.
| 12. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP (for Rear Door) |
![]() |
Install the rear door inner glass weatherstrip.
| 13. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY (for Rear Door) |
![]() |
Engage the guide and 2 claws to install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.
| 14. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY (for Rear Door) |
![]() |
Install the No. 1 door scuff plate clamp as shown in the illustration.
![]() |
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
Connect the connector.
![]() |
Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
| *1 | Reference Boss |
![]() |
Engage the 8 clips and install the rear door trim board sub-assembly.
Install the 3 screws.
If protective tape has been applied, remove it.
| 15. INSTALL REAR ARMREST ASSEMBLY (for Rear Door) |
![]() |
Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.
| 16. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (for Rear Door) |
Connect the connector.
![]() |
Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.
| 17. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG (for Rear Door) |
![]() |
Engage the 3 claws to install the rear door inside handle bezel plug.