Home › Power Source / Network ยท NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > FAIL-SAFE CHART

for Preparation Click here



FAIL-SAFE FUNCTION
  1. When communication fails in any of the CAN bus lines (communication lines), a fail-safe function(s) will operate. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.

  2. The following table shows the effects on each system when communication is impossible. (For further details, see the pages for each system.)

    Function
    Control Master
    System Related
    Fail-safe Operation
    Driver Detectable
    DTC Detection
    (ECU that stored DTC)
    Air conditioning control
    1. Corrects engine speed, such as for idle up
    2. Controls outlet air temperature, outlet mode change and airflow volume based on engine coolant temperature signal
    3. Corrects engine coolant temperature map and changes compressor lock judgment value
    Air conditioning amplifier assembly
    ECM
    Control is performed based on default coolant temperature of 80°C (176°F).
    -
    U0100
    (Air conditioning amplifier assembly)
    Compressor control
    1. Judges compressor lock according to engine speed
    Air conditioning amplifier assembly
    ECM
    Control is performed based on default engine speed of 0 rpm.
    -
    U0100
    (Air conditioning amplifier assembly)
    Simple load control
    1. Performs electric load control according to load control level signal
    Air conditioning amplifier assembly
    Power steering ECU with motor assembly
    Load control is not performed.
    -
    U0131
    (Air conditioning amplifier assembly)
    Panel dimming control
    1. Outputs dimmer signal to LIN connected panels according to display dimmer signal
    Air conditioning amplifier assembly
    Main body ECU (Multiplex network body ECU)
    Dimming mode and non-dimming mode cannot be switched.
    -
    U0142
    (Air conditioning amplifier assembly)
    Destination identification control
    1. Changes air conditioning control pattern according to destination
    Air conditioning amplifier assembly
    Main body ECU (Multiplex network body ECU)
    Maintains the latest state.
    -
    U0142
    (Air conditioning amplifier assembly)
    Ambient temperature correction control
    1. Switches air conditioning system operation condition and corrects value of displayed ambient temperature according to vehicle speed signal
    Air conditioning amplifier assembly
    Combination meter assembly
    Control is performed based on default vehicle speed of 0 km/h (0 mph).
    1. Correction level for displayed ambient temperature declines.
    2. Correction level for outlet airflow declines.
    U0155
    (Air conditioning amplifier assembly)
    Fuel Consumption display
    1. Displays graph of fuel consumption per minute and history of total fuel consumption
    1. Navigation ECU sub-assembly
    2. Radio and display receiver assembly
    1. ECM
    2. Brake actuator assembly
    3. Combination meter assembly
    When communication with ECM or skid control ECU is interrupted:
    1. Display is not updated.
    When communication with combination meter is interrupted:
    1. Display is not updated.
    2. Numeric part of driveable mileage is cleared.
    -
    U0100
    U0129
    U0155
    (Navigation ECU sub-assembly)
    (Radio and display receiver assembly)
    Parking assist monitor control
    1. Displays rear view monitor based on steering sensor, vehicle speed and vehicle information
    Navigation ECU sub-assembly
    1. Steering sensor
    2. Main body ECU (Multiplex network body ECU)
    When communication with steering angle sensor is interrupted:
    1. Message is shown indicating that guide lines cannot be displayed.
    -
    U0073
    U0126
    U0140
    (Navigation ECU sub-assembly)
    Destination identification
    1. Identifies destination based on destination and destination package information, and selects the time zone and language used for the display
    1. Navigation ECU sub-assembly
    2. Radio and display receiver assembly
    Main body ECU (Multiplex network body ECU)
    Destination is identified based on information received before communication is interrupted.
    Time zone and language selection screen are different from actual destination.
    U0140
    (Navigation ECU sub-assembly)
    (Radio and display receiver assembly)
    Vehicle customization function
    1. Allows changing of operation and control conditions for vehicle functions via multi-display operation
    1. Navigation ECU sub-assembly
    2. Radio and display receiver assembly
    1. Smart key ECU assembly (Certification ECU)
    2. Main body ECU (Multiplex network body ECU)
    1. Customization via multi-display is not possible, but customization via main body ECU is possible.
    2. When an application that uses remote communication is activated (customization/remote diagnosis), the process will be performed regardless of main body ECU remote communication permit/prohibit state.
    Customizable items are not displayed.
    U0073
    (Navigation ECU sub-assembly)
    Door lock
    1. Controls key linked and automatic door lock/unlock function, key confinement prevention function, etc.
    Main body ECU (Multiplex network body ECU)
    1. ECM
    2. Combination meter assembly
    1. Speed sensitive automatic lock control does not occur.
    2. Shift linked automatic lock control does not occur.
    3. Shift linked automatic unlock control does not occur.
    4. Automatic lock/unlock cannot be changed.
    -
    U0100
    U0155
    (Main body ECU (Multiplex network body ECU))
    Display automatic dimming
    1. Display dimming control
    Main body ECU (Multiplex network body ECU)
    Combination meter assembly
    Automatic dimming control for displays does not operate when taillights are turned on.
    -
    U0155
    (Main body ECU (Multiplex network body ECU))
    Illumination control
    Main body ECU (Multiplex network body ECU)
    1. ECM
    2. Smart key ECU assembly (Certification ECU)
    1. Interior lights turn off.
    2. Inside handle light turn off.
    When communication with smart key ECU is interrupted:
    1. Interior lights do not turn off right after getting out of the vehicle.
    U0100
    U0327
    (Main body ECU (Multiplex network body ECU))
    Entry function/wireless control
    Main body ECU (Multiplex network body ECU)
    Smart key ECU assembly (Certification ECU)
    Entry lock/unlock control is not possible.
    -
    U0327
    (Main body ECU (Multiplex network body ECU))
    Parking assist system control
    1. Judges shift lever position
    2. Judges vehicle speed
    Clearance warning ECU Assembly
    1. ECM
    2. TCM
    3. Combination meter assembly
    4. Main body ECU (Multiplex network body ECU)
    Obstacle detection is stopped.
    -
    When communication with ECM or TCM is interrupted:
    1. U0101
      (Clearance warning ECU Assembly)
    When communication with Main body ECU (Multiplex network body ECU) is interrupted:
    1. U0142 (Clearance warning ECU Assembly)
    When communication with combination meter is interrupted:
    1. U0155
      (Clearance warning ECU Assembly)
    Electric load control
    1. Performs idle up according to electric loads
    ECM
    1. Power steering ECU with motor assembly
    2. Main body ECU (Multiplex network body ECU)
    3. Air conditioning amplifier assembly
    Idle up according to electric loads is not performed.
    -
    -
    Air conditioning cooperative operation
    1. Performs idle up according to compressor load
    2. Performs air conditioning cut control
    ECM
    Air conditioning amplifier assembly
    Air conditioning system does not use cooperative controls.
    (Idle up is not performed.)
    Air conditioning system does not operate.
    -
    Charge control
    1. Performs idle up according to charging request
    Smart key ECU assembly (Certification ECU)
    1. Main body ECU (Multiplex network body ECU)
    2. Air conditioning amplifier assembly
    Idle up according to charging request is not performed.
    Taillights flicker and blower airflow changes.
    -
    Eco control
    1. Adjusts throttle response in consideration of actual fuel economy
    ECM
    1. Main body ECU (Multiplex network body ECU)
    2. Air conditioning amplifier assembly
    Eco mode does not operate.
    -
    -
    Coast downshift timing change according to air conditioning load
    1. Delays upshifts according to warm-up request
    1. ECM
    2. ECT
    Air conditioning amplifier assembly
    Coast downshift does not occur.
    Coast downshift shock reduction performance deteriorates.
    -
    Power steering control
    1. Calculates assist current according to torque sensor value and vehicle speed and drives motor
    Power steering ECU with motor assembly
    1. ECM
    2. Brake actuator assembly
    3. Steering sensor
    When communication with ECM is interrupted:
    1. Power steering assist not provided.
    When communication with skid control ECU is interrupted:
    1. Control continues based on a default speed of 100 km/h (62 mph) because vehicle speed is unrecognizable.
      (Steering wheel feels heavy when the vehicle speed is below 100 km/h (62 mph) and feels light at speeds above 100 km/h (62 mph).)
    EPS warning light illuminates.
    U0100
    U0129
    (Power steering ECU with motor assembly)
    Steering assist calculation
    1. Changes assist force based on vehicle speed
    Power steering ECU with motor assembly
    Brake actuator assembly
    Control continues based on a default speed of 100 km/h (62 mph) because vehicle speed is unrecognizable.
    (Steering wheel feels heavy when the vehicle speed is below 100 km/h (62 mph) and feels light at speeds above 100 km/h (62 mph).)
    EPS warning light illuminates.
    U0129
    (Power steering ECU with motor assembly)
    Steering/steering angle sensor initialization and zero point learning
    Power steering ECU with motor assembly
    Brake actuator assembly
    Steering initialization and zero point learning are not performed.
    EPS warning light illuminates.
    U0129
    (Power steering ECU with motor assembly)
    Assist map selection
    1. Selects proper assist map according to destination, engine type, etc.
    Power steering ECU with motor assembly
    1. ECM
    2. Brake actuator assembly
    Default map is used to assist because proper assist map cannot be selected.
    (Steering feel may be different.)
    EPS warning light illuminates.
    U0100
    U0129
    (Power steering ECU with motor assembly)
    Entry function
    1. Entry lock/unlock, entry luggage compartment open
    2. Warning
    3. Performs entry illumination
      (Interior illumination etc)
    1. Main body ECU (Multiplex network body ECU)
    2. Smart key ECU assembly (Certification ECU)
    1. Main body ECU (Multiplex network body ECU)
    2. Combination meter assembly
    Entry unlock is performed again.
    1. Entry lock/unlock or entry luggage compartment open does not operate.
    2. Warning functions (Key confinement, Key not in vehicle, Key reminder etc.) do not operate, Key confinement prevention control does not operate.
    3. Entry illumination does not operate.
    U0142
    U0155
    (Smart key ECU assembly (Certification ECU))
    Wireless function
    1. Locks and unlocks doors, etc. via remote operation
    Main body ECU (Multiplex network body ECU)
    Smart key ECU assembly (Certification ECU)
    Wireless lock, unlock and luggage compartment opener do not operate
    -
    -
    Engine switch backlighting control
    1. Turns on/off engine switch illumination linked with interior lights etc.
    Smart key ECU assembly (Certification ECU)
    Main body ECU (Multiplex network body ECU)
    Engine switch backlighting does not illuminate according to interior lights operation
    -
    U0142
    (Smart key ECU assembly (Certification ECU))
    Meter display
    1. Displays vehicle condition and controls indicator lights
    Combination meter assembly
    1. ECM
    2. Brake actuator assembly
    3. Airbag sensor assembly
    4. Power steering ECU with motor assembly
    5. Main body ECU (Multiplex network body ECU)
    Lights do not illuminate or lights always illuminate
    Lights do not illuminate properly or do not illuminate at all.
    U0100
    U0129
    U0131
    U0142
    U0151
    (Combination meter assembly)
    Vehicle speed display
    Combination meter assembly
    Brake actuator assembly
    Vehicle speed display remains at 0 km/h (0 mph).
    -
    U0129
    (Combination meter assembly)
    Tachometer
    1. Displays engine speed
    Combination meter assembly
    ECM
    The needle points at 0 rpm.
    -
    U0100
    (Combination meter assembly)
    Coolant temperature display
    Combination meter assembly
    ECM
    Display is turned off.
    -
    -
    Engine start/stop switch
    (Power source mode change)
    1. Using start/stop switch signal as trigger, changes power source mode automatically and requests starter operation when conditions are met
    Smart key ECU assembly (Certification ECU)
    ECM
    -
    -
    U0100
    (Smart key ECU assembly (Certification ECU))
    ABS/TRC/VSC control
    Brake actuator assembly
    1. ECM
    2. Steering sensor
    3. Airbag sensor assembly (built-in type yaw rate sensor)
    4. Yaw rate sensor (separate type yaw rate sensor)
    Control stops
    Warning lights and indicators illuminate.
    U0073
    U0100
    U0123
    U0126
    (Brake actuator assembly)
    Power tilt and power telescopic steering column control
    (Starts steering wheel auto return or auto away based on a key removal or insertion signal or equivalent)
    Multiplex tilt and telescopic ECU
    Main body ECU (Multiplex network body ECU)
    -
    Auto return/away control does not operate.
    U0142
    (Multiplex tilt and telescopic ECU))
    Lighting system
    1. Adjusts headlights vertical aiming according to wheel speed and vehicle pitch angle determined using vehicle height sensor.
    2. Swings headlights left or right according to wheel speed and turn radius determined using steering angle.
    AFS ECU
    1. ECM
    2. TCM
    3. Brake actuator assembly
    4. Steering sensor
    5. Main body ECU (Multiplex network body ECU)
    Control stops
    AFS indicator blinks.
    U0100
    U0101
    U0126
    U0129
    U0142
    (AFS ECU)