FIT STANDARD / ADJUSTMENT METHOD > ADJUSTMENT



INSPECT HOOD SUB-ASSEMBLY

B277176E01

  1. Check that the clearance measurements of areas a through d are within each standard range.


Reference Value 
Area
Measurement
Area
Measurement
a
2.45 to 6.45 mm (0.0965 to 0.254 in.)
b
3.55 to 7.55 mm (0.140 to 0.297 in.)
c
2.0 to 5.0 mm (0.0787 to 0.197 in.)
d
-1.5 to 1.5 mm (-0.0591 to 0.0591 in.)

HINT:
Centering bolts are used to mount the hood hinge and hood lock. The hood and hood lock cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.


ADJUST HOOD SUB-ASSEMBLY
B277161
  1. Horizontally and vertically adjust the hood.

    1. Loosen the 4 hinge bolts of the hood.

    2. Adjust the clearance between the hood and front fender by moving the hood.

    3. Tighten the 4 hinge bolts after the adjustment.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }



  2. B277162
  3. Adjust the height of the front end of the hood using the cushion rubbers.

    1. Adjust the 2 cushion rubbers so that the heights of the hood and fender are aligned.

      HINT:
      Raise or lower the front end of the hood by turning the 2 cushion rubbers.

  4. Remove the radiator grille sub-assembly.



  5. B277164
  6. Adjust the hood lock.

    1. Loosen the 3 bolts.

    2. Adjust the hood lock and tighten the 3 bolts.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    3. Check that the striker can engage with the hood lock smoothly.

  7. Install the radiator grille sub-assembly.


INSPECT FRONT DOOR

B277177E01

  1. Check that the clearance measurements of areas a through p are within each standard range.


Reference Value 
Area
Measurement
Area
Measurement
a
3.35 to 6.35 mm (0.132 to 0.250 in.)
b
9.0 to 12.0 mm (0.354 to 0.472 in.)
c
3.35 to 6.35 mm (0.132 to 0.250 in.)
d
1.7 to 4.7 mm (0.0669 to 0.185 in.)
e
3.35 to 6.35 mm (0.132 to 0.250 in.)
f
1.0 to 4.0 mm (0.0394 to 0.157 in.)
g
2.3 to 6.3 mm (0.0906 to 0.248 in.)
h
2.96 to 4.64 mm (0.115 to 0.182 in.)
i
-0.84 to 0.84 mm (-0.0331 to 0.0331 in.)
j
2.96 to 4.64 mm (0.115 to 0.182 in.)
k
-0.84 to 0.84 mm (-0.0331 to 0.0331 in.)
l
2.9 to 7.1 mm (0.114 to 0.280 in.)
m
2.3 to 4.7 mm (0.0906 to 0.185 in.)
n
-1.2 to 1.2 mm (-0.0472 to 0.0472 in.)
o
2.3 to 4.7 mm (0.0906 to 0.185 in.)
p
-1.2 to 1.2 mm (-0.0472 to 0.0472 in.)

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.
  3. Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.


REMOVE FRONT WHEEL

REMOVE FRONT FENDER SEAL
B280591
  1. Disengage the 3 clips and remove the front fender seal.


ADJUST FRONT DOOR

NOTICE:
Make sure that the turn the ignition switch off when adjusting door lock strikers.



    B280380
  1. Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

    SST
    09812-00010  

  2. Tighten the hinge bolts on the vehicle body after adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  3. Loosen the hinge bolts on the door and adjust the door position.

  4. Tighten the hinge bolts on the door after adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



  5. B280382
  6. Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.

  7. Using a brass bar and a hammer, hit the striker to adjust its position.

  8. Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }


INSTALL FRONT FENDER SEAL
B280591
  1. Install the front fender seal with new 3 clips.


INSTALL FRONT WHEEL

INSPECT REAR DOOR

B277178E01

  1. Check that the clearance measurements of areas a through r are within each standard range.


Reference Value 
Area
Measurement
Area
Measurement
a
3.35 to 6.35 mm (0.132 to 0.250 in.)
b
0.6 to 3.6 mm (0.0236 to 0.142 in.)
c
3.35 to 6.35 mm (0.132 to 0.250 in.)
d
0.9 to 3.9 mm (0.0354 to 0.154 in.)
e
3.35 to 6.35 mm (0.132 to 0.250 in.)
f
1.5 to 4.5 mm (0.0591 to 0.177 in.)
g
3.35 to 6.35 mm (0.132 to 0.250 in.)
h
5.4 to 8.4 mm (0.213 to 0.331 in.)
i
-1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
j
2.0 to 5.0 mm (0.0787 to 0.197 in.)
k
2.0 to 5.0 mm (0.0787 to 0.197 in.)
l
-1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
m
2.9 to 7.1 mm (0.114 to 0.280 in.)
n
2.96 to 4.64 mm (0.115 to 0.182 in.)
o
-0.84 to 0.84 mm (-0.0331 to 0.0331 in.)
p
2.96 to 4.64 mm (0.115 to 0.182 in.)
q
-0.84 to 0.84 mm (-0.0331 to 0.0331 in.)
r
2.3 to 6.3 mm (0.0906 to 0.248 in.)

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.
  3. Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.


ADJUST REAR DOOR

NOTICE:
Make sure that the turn the ignition switch off when adjusting door lock strikers.



    B280548
  1. Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

    SST
    09812-00010  

  2. Tighten the hinge bolts on the vehicle body after the adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  3. Loosen the hinge bolts on the door and adjust the door position.

  4. Tighten the hinge bolts on the door after the adjustment.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



  5. B280549
  6. Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.

  7. Using a brass bar and a hammer, hit the striker to adjust its position.

  8. Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }


INSPECT LUGGAGE COMPARTMENT DOOR

B277179E01

  1. Check that the clearance measurements of areas a through d are within each standard range.


Reference Value 
Area
Measurement
Area
Measurement
a
6.4 mm (0.252 in.)
b
2.0 to 5.0 mm (0.0787 to 0.197 in.)
c
-1.0 to 2.0 mm (-0.0394 to 0.0787 in.)
d
3.85 to 7.85 mm (0.152 to 0.309 in.)

HINT:
Centering bolts are used to mount the door hinge to the door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.


ADJUST LUGGAGE COMPARTMENT DOOR
B280559
  1. Loosen the door side hinge bolts to adjust the door horizontally and vertically.

    Torque:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }



  2. B280560
  3. Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.

  4. Using a brass bar and a hammer, hit the striker to adjust its position.

  5. Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }