BODY STRUCTURE > DETAILS |
| FUNCTION |
Safety Features
Impact Absorbing Structure for Frontal Collision

| *1 | Front Side Member | *2 | Beltline Reinforcement |
![]() | Impact | ![]() | Impact Flow |
Impact Absorbing Structure for Side Collision

| *1 | Center Pillar Outer Reinforcement | *2 | Front Floor Crossmember |
| *3 | Center Floor Crossmember | *4 | Roof Reinforcement |
| *5 | Rocker Panel Reinforcement | *6 | Impact Protect Beam |
| *7 | Impact Support Box | *8 | Seat Pipe |
| *9 | Rear Door Box | *10 | Center Crossmember Gusset |
![]() | Impact | ![]() | Impact Flow |

![]() | Impact | ![]() | Impact Flow |
Impact Absorbing Structure for Rear Collision
Lessening Pedestrian Injury

| *1 | Longitudinal Ribbed Structure | *2 | Dent Reinforcement (Impact Absorbing Structure) |

| *1 | Impact Absorbing Bracket (Front) | *2 | Impact Absorbing Bracket (Rear) |
| *a | A-A Cross Section | *b | B-B Cross Section |
| *c | Before Collision | *d | After Collision |
![]() | Impact | - | - |

| *1 | Window Shield Glass | *2 | Cowl Top Panel Sub-assembly |
| *a | A-A Cross Section | *b | Before Collision |
| *c | After Collision | - | - |
![]() | Impact | - | - |
Aerodynamics
An aero stabilizing fin is provided on the outer rear view mirror base and on the rear combination light lens for enhanced aerodynamics.

| *a | Aero Stabilizing Fin | *b | Vortex |
![]() | Airflow | ![]() | Hold the Vehicle from Both Side |
The height, angle, and shape of the front bumper have been optimized, resulting in smooth airflow underneath the floor.

| *1 | Front Bumper | - | - |
![]() | Airflow | - | - |
Various types of airflow routing parts are provided under the floor to control airflow. In addition, an undercover is provided to make the under floor area flat in order to ensure excellent aerodynamic performance.
A fin-shaped engine under cover and rear under cover have been adopted to achieve higher diffuser efficiency, thereby ensuring stability.

![]() | Undercover Area | - | - |
| CONSTRUCTION |
Lightweight and Highly Rigid Body
High strength steel and ultra high strength steel are used in order to realize excellent body rigidity and a lightweight body.

| *1 | High Strength Steel | *2 | Ultra High Strength Steel |
Rust-resistant Body
Anti-corrosion steel sheet is used as shown in the following illustration:

| *A | Models with Roof Sliding System | - | - |
![]() | Anti-corrosion Steel Sheet | - | - |
For rust resistance, sealant has been applied to the floor panel to prevent water from entering through the mating surfaces of the panels. Undercoating has been also applied to reduce damage to the body from chipping, contributing to rust resistance.

| *a | Sealant | - | - |
![]() | Under Coat | - | - |
Body Shell Construction
The cowl top panel sub-assembly outer is used to connect the left and right front spring supports , which is straight, improving lateral rigidity and ensuring front suspension input point rigidity and body rigidity.

| *1 | Cowl Top Panel Sub-assembly | - | - |
A closed shape has been adopted for the upper back panel. The upper back panel is used to connect the left and right back side panels, which is straight, improving light weight yet body rigidity.

| *1 | Under Back Panel | - | - |
Along with the optimal positioning of frame components such as rear side members, center floor members, rear floor crossmember and rear sub-frame the usage of a small number of parts has realized a lightweight design while also ensuring an excellent rigidity and handling stability.

| *1 | Rear Side Member | *2 | Center floor Crossmember |
| *3 | Rear floor Crossmember | *4 | Rear Sub-frame |
Low Vibration and Low Noise Body
The following body structures are used, in order to reduce panel vibration and body frame movement.
| Panel vibration reduction structure |
|

| *1 | Cross Member of The Dash Panel | *2 | Tunnel Reinforcement |
| *3 | Floor Pan Panel | *4 | Bead |
Damping coatings are provided, combining enhanced quietness and reduced weight.

![]() | Damping Coating | - | - |
Silencer pads are provided on the engine compartment side and cabin side of the dash panel, minimizing penetration of engine noise and road noise into the cabin.

| *1 | Dash Panel Insulator Outer | *2 | Dash Panel |
| *3 | Dash Panel Insulator Inner | - | - |
The layout of the sound-absorbing material is optimized to reduce noise and vibration.

| *a | A-A Cross Section | *b | B-B Cross Section |
| *c | C-C Cross Section | - | - |
![]() | Sound-absorbing Material | - | - |
Silencers are provided inside the rear wheel housings to minimize the penetration into the cabin of splashing noise generated in the wheel housings.

| *1 | Rear Wheel House Silencer | - | - |
| *a | A-A Cross Section | - | - |
Weatherstrips are provided for the front and rear doors at the rocker panel to minimize the penetration of road noise into the cabin.

| *1 | Weatherstrip | - | - |
| *a | A-A Cross Section | - | - |
Parts that Reduce Overall Damage
A concave design has been adopted for the front bumper absorber. This helps prevent the vehicle from going under obstacles in the event of a collision.

| *1 | Front Bumper Absorber | *2 | Front Bumper Reinforcement |
| *3 | Obstacles | - | - |
| *a | Before Collision | *b | After Collision |