METER / GAUGE SYSTEM > GENERAL



OUTLINE


  1. Combination Meter Assembly

    1. An analog type combination meter assembly is provided as standard on models for U.S.A. and Canada.

    2. An Optitron type combination meter assembly is provided as standard on the destination package for South Korea.

    3. The combination meter assembly has a built-in meter ECU and buzzer.

    4. A wide type Liquid Crystal Display (LCD) is provided for the combination meter assembly on non-grade models for U.S.A.. On the remaining models, 2 LCDs are provided.

    5. The Optitron type combination meter assembly has a multi-information display.



    6. The maintenance requirement reminder function is provided on models for U.S.A. to inform the driver when maintenance is necessary.


      Y111595E01


      Text in Illustration (Models for U.S.A.:) 
      *A
      Non-Grade
      *B
      LE Grade
      *1
      Rheostat Switch
      *2
      LCD
      *3
      ODO/TRIP Switch
      -
      -

      Y111596E01


      Text in Illustration (Models for U.S.A.:) 
      *A
      SE Grade
      *B
      XLE Grade
      *1
      Rheostat Switch
      *2
      LCD
      *3
      ODO/TRIP Switch
      -
      -

      Y111597E01


      Text in Illustration (Models for Canada:) 
      *A
      LE Grade
      *B
      SE Grade
      *1
      Rheostat Switch
      *2
      LCD
      *3
      ODO/TRIP Switch
      -
      -

      Y111598E01


      Text in Illustration (Models for Canada and Destination Package for South Korea:) 
      *A
      XLE Grade for Canada
      *B
      XLE Grade for South Korea
      *1
      Rheostat Switch
      *2
      LCD
      *3
      Multi-information Display
      *4
      ODO/TRIP Switch


MAIN FEATURES
  1. Combination Meter Assembly

    1. An illumination control which allows for anticipation of a pleasant drive is used. If the ignition switch is turned to ON, the illumination control operates as follows:

      1. When the ignition switch is turned to ON, the opening display appears on the multi-information display.*
      2. The following illuminations fade in: the speedometer, tachometer, fuel gauge, fuel consumption meter needle indicator, 2 LCD displays and meter panel illumination.

      3. When the ignition switch is turned off, all the illuminations fade out. During this period, the multi-information display shows the Eco drive level for 3 seconds.*
        *: Models with multi-information display


        Y111599


        Text in Illustration (Models without Multi-information Display:) 
        V100136
        Ignition switch off to ON
        V100135
        Ignition switch ON to off


        Y111600


        Text in Illustration (Models with Multi-information Display:) 
        V100136
        Ignition switch off to ON
        V100135
        Ignition switch ON to off



  2. Fuel Consumption Gauge

    1. A needle indicator type average fuel consumption gauge is provided on the combination meter assembly. The needle indicator indicates the value in accordance with the average fuel consumption value displayed on the ODO/TRIP meter*1 or multi-information display*2.



    2. On XLE grade models, an instantaneous fuel consumption gauge is provided. This gauge is a segment type indicator and is arranged outside the average fuel consumption gauge. This arrangement enables the driver to check the average and instantaneous fuel consumption simultaneously, assisting eco-friendly driving.

      1. *1: Models with analog type combination meter assembly
      2. *2: Models with Optitron type combination meter assembly

      Y111601E01


      Text in Illustration 
      *A
      XLE Grade Only
      -
      -
      *1
      Average Fuel Consumption Gauge
      *2
      Instantaneous Fuel Consumption Gauge

  3. LCD

    1. On non-grade models for U.S.A., a wide type Liquid Crystal Display (LCD) is provided. This display shows the following information:

      Item
      Outline
      LCD
      1. The following information items are always displayed.
        1. Shift Position Indicator
        2. Engine Coolant Temperature Gauge (segment type display)
        3. Ambient Temperature
      2. When the rheostat switch is pressed, the engine coolant temperature gauge will change into an indicator for meter illumination adjustment mode. The meter illumination can be switched between 6 levels.
      1. The following information items can be displayed. The item shown can be changed by pressing the ODO/TRIP switch.
        1. Odometer
        2. Trip Meter A
        3. Trip Meter B
        4. Ambient Temperature
        5. Average Fuel Consumption
        6. Current Fuel Consumption
      2. Pressing and holding the ODO/TRIP switch while the odometer is displayed changes the odometer to an on/off mode that enables or disables the operation of Eco Driving Indicator Light.

    2. On models other than non-grade models for U.S.A., 2 LCDs are provided. Each display shows the following information.

      Item
      Outline
      LCD (Tachometer Side)
      1. The following information items are always displayed.
        1. Shift Position Indicator
        2. Engine Coolant Temperature Gauge (segment type display)
        3. Ambient Temperature
      2. When the rheostat switch is pressed, the engine coolant temperature gauge will change into an indicator for meter illumination adjustment mode. The meter illumination can be switched between 6 levels.
      LCD (Fuel Gauge Side)
      1. The following information items can be displayed. The item shown can change by pressing the ODO/TRIP switch.
        1. Odometer
        2. Trip Meter A
        3. Trip Meter B
        4. Average Fuel Consumption
      2. Pressing and holding the ODO/TRIP switch while the odometer is displayed changes the odometer to an on/off mode that enables or disables the operation of Eco Driving Indicator Light and instantaneous fuel consumption*.

      1. *: XLE grade models

  4. Multi-information Display

    1. The Optitron type combination meter assembly incorporates a multi-information display.

    2. The multi-information display shows the following information.

      Mode
      Outline
      Cruise Information
      1. The item shown can be change by pushing the DISP switch in the steering pad switch assembly.
      2. In cruise information mode, the following information can be displayed:
        1. Cruising Range and Average Fuel Consumption
        2. Average Vehicle Speed and Elapsed Time
        3. Eco Drive Level
        4. Settings
      3. Blank Screen
      Clearance Sonar Display*
      The obstruction detection state of the clearance sonars is displayed.
      Warning
      The warning display will interrupt the multi-information display immediately when a warning occurs.
      Customization
      1. The following display, performance or illumination of the combination meter assembly can be customized:
        1. Language
        2. Eco Driving Indicator Light and instantaneous fuel consumption gauge

      1. *: Models with intuitive parking assist system


PRECAUTION
  1. Ignition Switch Expressions

    1. The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

      Expression
      Ignition Switch
      (Position)
      Engine Switch
      (Condition)
      Ignition Switch off
      LOCK
      Off
      Ignition Switch ACC
      ACC
      On (ACC)
      Ignition Switch ON
      ON
      On (IG)
      Engine Start
      START
      Start