BLIND SPOT MONITOR SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS

Component
Function
Blind Spot Monitor Sensor LH and RH
  1. Radiates radar waves from the blind spot monitor sensor to the blind spot sensor detection area, uses the reflected millimeter waves for detecting the presence of a vehicle, the vehicle-to-vehicle distance, and the relative speed, and then transmits this information to the built-in signal processing circuit.
  2. The signal processing circuit determines if a vehicle is present, and illuminates or blinks the outer rear view mirror indicator light accordingly.
Blind Spot Monitor Main Switch (Warning Canceling Switch Assembly)
Pressing the blind spot monitor main switch (warning canceling switch assembly) turns the blind spot monitor system on or off.
Outer Rear View Mirror Assembly LH and RH
Outer Rear View Mirror Indicator Light
  1. Illuminates to inform the driver that a vehicle has been detected in the blind spot detection area.
  2. Flashes to inform the driver when the turn signal lever is operated if a vehicle has been detected in the blind spot detection area.
Combination Meter Assembly
Transmits the turn switch signal to the blind spot monitor sensor LH and RH.
Combination Meter Assembly
Blind Spot Monitor Warning Light
When the blind spot monitor sensors detect a malfunction or determine that control is not possible, the light illuminates to warn the driver.
Steering Sensor
Transmits the steering angle signal to the blind spot monitor sensor LH and RH.
Skid Control ECU
Transmits the vehicle speed signal to the blind spot monitor sensor LH and RH.
Main Body ECU (Multiplex Network Body ECU)
Transmits the destination signal to the blind spot monitor sensor LH and RH.
Network Gateway ECU
Transmits data between the CAN V bus and the CAN sub bus 2.
ECM
Transmits the reverse signal to the blind spot monitor sensor LH and RH.

OPERATING CONDITION
  1. The blind spot monitor system operates when both of the following conditions are met:

    1. The blind spot monitor main switch (warning canceling switch assembly) is on.

    2. The vehicle speed is greater than about 40 km/h (25 mph).



  2. The blind spot monitor system can detect vehicles in its detection areas.



    1. The detection areas formed by the blind spot monitor sensor LH and RH are as shown below.


      Y110644E01


      Text in Illustration (Detection Area:) 
      *a
      3.5 m (11.5 ft)
      *b
      3.0 m (9.8 ft)
      *c
      1 m (3.3 ft)
      *d
      0.5 m (1.6 ft)
      V100144
      Detection Area
      -
      -



    2. This vehicle is overtaken by another vehicle in the adjacent lane.


      Y110645E01


      Text in Illustration 
      *1
      This Vehicle
      -
      -
      V100135
      Vehicle Speed (Fast)
      V100136
      Vehicle Speed (Slow)
      V100144
      Detection Area
      -
      -



    3. When another vehicle enters the detection area of this vehicle due to a lane change.


      Y110646E01


      Text in Illustration 
      *1
      This Vehicle
      -
      -
      *a
      Other vehicle enters the detection area during lane change (merge in) (Type 1).
      *b
      Other vehicle enters the detection area during lane change (merge in) (Type 2).
      V100135
      Motion direction of this vehicle
      V100136
      Motion direction of other vehicle
      V100144
      Detection Area
      -
      -


CONSTRUCTION


  1. Blind Spot Monitor Sensor

    1. The blind spot monitor sensor consists of a millimeter wave radar circuit and signal processing circuit.



    2. The millimeter wave radar uses frequencies in the 24 GHz band.


      Y110647E01


      Text in Illustration 
      *1
      Blind Spot Monitor Sensor LH
      *2
      Blind Spot Monitor Sensor RH
      *a
      Distance: Approximately 10 m (32.8 ft.)
      *b
      Horizontal Angle: Approximately 150°
      *c
      Vertical Angle: Approximately 20°
      -
      -

    3. The distance to the object, azimuth, and relative speed are calculated from the information that is provided by the reflected millimeter wave radar as described below.

      Item
      Calculation Method
      Distance
      Calculated from the length of time that has elapsed from the time the waves of the millimeter wave radar have been emitted, until the reflected waves are received by the millimeter wave radar circuit. The distance is approximately 10 m (32.8 ft.).
      Azimuth
      Calculated from the reception angle of the millimeter wave radar reflections received. The detection angle has a horizontal range of approximately 150° and a vertical range of approximately 20°.
      Relative Speed
      Calculated by utilizing the change (Doppler effect*) that occurs in the frequency of the reflected millimeter wave radar waves.

      HINT:
      *: The Doppler effect causes the observer to perceive the radio waves emitted by a moving object to be a higher frequency as it approaches, and to be a lower frequency at it recedes. This phenomenon is created because when an object is located far away, the radio waves are perceived at higher frequencies than those of the radio source. An SST is used if radar axis confirmation is needed. For details, refer to the Repair Manual.


OPERATION
  1. According to operation conditions, the blind spot monitor system promotes safety confirmation by using the outer rear view mirror indicator light to inform the driver that another vehicle has entered the blind spot monitor sensor detection area of this vehicle.



  2. The outer rear view mirror indicator light informs the driver that a vehicle is present in the blind spot detection area by illuminating when the turn signal switch is not operated, and by flashing when a vehicle is present and the turn signal switch is operated.


    Y110648E01


DIAGNOSIS
  1. The blind spot monitor system is equipped with a diagnosis function which can illuminate the blind spot monitor warning light in the combination meter assembly. For details, refer to the Repair Manual.