PARKING BRAKE ASSEMBLY > REASSEMBLY |
| 1. APPLY HIGH TEMPERATURE GREASE |
![]() |
Apply high temperature grease to the areas of the parking brake plate which make contact with the shoe as shown in the illustration.
![]() | High Temperature Grease |
| 2. INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN |
Install the 2 parking brake shoe hold down spring pins.
| 3. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side) |
Install the parking brake shoe return tension spring to the No. 2 parking brake shoe assembly.
| 4. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY |
Install the No. 1 parking brake shoe assembly to the parking brake shoe return tension spring.
| 5. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET |
![]() |
Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.
![]() | High Temperature Grease |
Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.
| 6. INSTALL PARKING BRAKE SHOE LEVER |
![]() |
Using needle-nose pliers, install the parking brake shoe lever to the No. 3 parking brake cable assembly.
![]() |
Apply high temperature grease to the areas of the parking brake shoe lever which make contact with the No. 2 parking brake shoe assembly.
![]() | High Temperature Grease |
![]() |
Install the parking brake shoe lever to the No. 2 parking brake shoe assembly.
Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and fit them to the parking brake plate.
| 7. INSTALL PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Rear Side) |
![]() |
Using SST, install the parking brake shoe hold down compression spring.
| 8. INSTALL PARKING BRAKE SHOE STRUT |
Install the parking brake shoe strut.
![]() |
Install the No. 1 parking brake shoe assembly.
| 9. INSTALL PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Front Side) |
![]() |
Using SST, install the parking brake shoe hold down compression spring.
| 10. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Rear Side) |
![]() |
Apply a small amount of high temperature grease to the areas shown in the illustration.
![]() | High Temperature Grease |
Install the parking brake shoe return tension spring.
| 11. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Front Side) |
Install the parking brake shoe return tension spring.
| 12. CHECK PARKING BRAKE INSTALLATION |
Check that each part is installed properly.

| *A | LH Side | *B | RH Side |
![]() | Front of the Vehicle | - | - |
| 13. INSTALL REAR DISC |
![]() |
Align the matchmarks of the rear disc and rear axle hub, and install the rear disc.
| *a | Matchmark |
| 14. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG |
| 15. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY |
Install the rear disc brake caliper assembly with the 2 bolts.
Install the rear flexible hose to the rear shock absorber with the bolt.
| 16. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL |
Completely release the parking brake pedal.
![]() |
Loosen the lock nut and the adjusting nut to completely release the parking brake cable.
| *1 | Lock Nut |
| *2 | Adjusting Nut |
Remove the rear wheels.
Temporarily install the hub nuts to the hub bolts.
Remove the parking brake shoe adjusting hole plug.
![]() |
Turn the shoe adjuster and expand the shoes until the disc locks.
![]() | Expand |
![]() | Contract |
Turn and contract the shoe adjuster until the disc can rotate smoothly.
Check that there is no brake drag against the shoe.
Install the parking brake shoe adjusting hole plug.
Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.
Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.
Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.
Check that the parking brake does not drag.
Remove the hub nuts from the hub bolts.
Install the rear wheels.
| 17. INSTALL REAR WHEEL |
| 18. BED IN PARKING BRAKE SHOES TO DISCS |
Drive the vehicle at about 50 km/h (31 mph) on a safe, level and dry road.
Depress the parking brake pedal with 150 N (15 kgf, 33.7 lbf) of force.
Drive the vehicle for about 400 m (0.25 mile) in this condition.
Repeat this procedure 3 times.