FRONT BRAKE > INSTALLATION |
| 1. INSTALL FRONT DISC |
![]() |
Align the matchmarks of the front disc and front axle hub, and install the front disc.
| *a | Matchmark |
| 2. INSTALL FRONT DISC BRAKE BUSHING DUST BOOT |
Secure the front disc brake cylinder mounting in a vise.
![]() |
Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.
![]() | Lithium Soap Base Glycol Grease |
![]() |
Using a socket wrench (19 mm) and a hammer, install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.
| 3. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING |
![]() |
Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.
| 4. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSHING |
![]() |
Apply a light layer of lithium soap base glycol grease to the contact surface of the No. 2 front disc brake cylinder slide pin.
![]() | Lithium Soap Base Glycol Grease |
Install a new front disc brake cylinder slide bushing to the front No. 2 disc brake cylinder slide pin.
| 5. INSTALL FRONT NO. 2 DISC BRAKE CYLINDER SLIDE PIN |
![]() |
Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front No. 2 disc brake cylinder slide pin.
![]() | Lithium Soap Base Glycol Grease |
![]() |
Install the front No. 2 disc brake cylinder slide pin to the front disc brake cylinder mounting.
Push the front No. 2 disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.
| 6. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN |
![]() |
Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front disc brake cylinder slide pin.
![]() | Lithium Soap Base Glycol Grease |
![]() |
Install the front disc brake cylinder slide pin to the front disc brake cylinder mounting.
Push the front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.
| 7. INSTALL FRONT DISC BRAKE FITTING KIT |
![]() |
Install the 2 front No. 1 disc brake pad support plates and 2 front No. 2 disc brake pad support plates to the front disc brake cylinder mounting.
| *1 | Front No. 1 Disc Brake Pad Support Plate |
| *2 | Front No. 2 Disc Brake Pad Support Plate |
| 8. INSTALL FRONT ANTI-SQUEAL SHIM KIT |
![]() |
Install the front disc brake pad wear indicator plate to each front disc brake pad.
![]() |
Apply disc brake grease to the inside of each front disc brake anti-squeal shim as shown in the illustration.
![]() | Disc Brake Grease |
![]() |
Install the front disc brake anti-squeal shim to each front disc brake pad.
| 9. INSTALL FRONT DISC BRAKE PAD KIT |
Install the 2 front disc brake pads with front anti-squeal shim kit to the front disc brake cylinder mounting.
![]() |
Install the 2 anti-squeal springs to the front disc brake pads.
| 10. INSTALL DISC BRAKE CYLINDER ASSEMBLY |
![]() |
Hold the front disc brake cylinder slide pin, and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.
| *a | Hold |
| *b | Turn |
| 11. CONNECT FRONT FLEXIBLE HOSE |
![]() |
Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.
| *a | Lock Hole |
| 12. BLEED BRAKE LINE |
| 13. INSTALL FRONT WHEEL |