Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



A247842E20

HINT:
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A25-1 (BATT) - E26-16 (E1)
GR - BR
Battery (for measuring battery voltage and for ECM memory)
Always
11 to 14 V
E26-29 (+BM) - E26-16 (E1)
R - BR
Power source of throttle actuator
Always
11 to 14 V
A25-37 (IGSW) - E26-16 (E1)
V - BR
Ignition switch signal
Ignition switch ON
11 to 14 V
A25-2 (+B) - E26-16 (E1)
P - BR
Power source of ECM
Ignition switch ON
11 to 14 V
A25-3 (+B2) - E26-16 (E1)
LG - BR
Power source of ECM
Ignition switch ON
11 to 14 V
E26-74 (OC1+) - E26-75 (OC1-)
W - B
Camshaft timing oil control valve assembly operation signal (for intake camshaft)
Idling
Pulse generation
(See waveform 1)
E26-65 (OE1+) - E26-64 (OE1-)
R - GR
Camshaft timing oil control valve assembly operation signal (for exhaust camshaft)
Idling
Pulse generation
(See waveform 2)
A25-46 (MREL) - E26-16 (E1)
BE - BR
EFI MAIN relay operation signal
Ignition switch ON
11 to 14 V
E26-91 (VG) - E26-92 (E2G)
G - LG
Mass air flow meter sub-assembly signal
Idling, shift lever in P, A/C switch off
0.5 to 3.0 V
E26-93 (THA) - E26-94 (ETHA)
P - Y
Intake air temperature sensor signal
Idling, intake air temperature 20°C (68°F)
0.5 to 3.4 V
E26-95 (THW) - E26-96 (ETHW)
B - P
Engine coolant temperature sensor signal
Idling, engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
E26-125 (VCTA) - E26-126 (ETA)
B - R
Power source of throttle position sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
E26-127 (VTA1) - E26-126 (ETA)
Y - R
Throttle position sensor signal (for engine control)
Ignition switch ON,
accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON,
accelerator pedal fully depressed
3.2 to 4.8 V
E26-128 (VTA2) - E26-126 (ETA)
W - R
Throttle position sensor signal (for sensor malfunction detection)
Ignition switch ON,
accelerator pedal fully released
2.1 to 3.1 V
Ignition switch ON,
accelerator pedal fully depressed
4.6 to 5.0 V
A25-51 (VPA) - A25-52 (EPA)
G - Y
Accelerator pedal position sensor signal (for engine control)
Ignition switch ON,
accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON,
accelerator pedal fully depressed
2.6 to 4.5 V
A25-54 (VPA2) - A25-55 (EPA2)
R - BE
Accelerator pedal position sensor signal (for sensor malfunction detection)
Ignition switch ON,
accelerator pedal fully released
1.2 to 2.0 V
Ignition switch ON,
accelerator pedal fully depressed
3.4 to 5.0 V
A25-53 (VCPA) - A25-52 (EPA)
P - Y
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.5 V
A25-56 (VCP2) - A25-55 (EPA2)
L - BE
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.5 V
E26-23 (HA1A) - E26-53 (E04)
G - W-B
Air fuel ratio sensor heater operation signal
Idling
Pulse generation
(See waveform 3)
Ignition switch ON
11 to 14 V
E26-133 (A1A+) - E26-16 (E1)
L - BR
Air fuel ratio sensor signal
Ignition switch ON
3.3 V*1
E26-134 (A1A-) - E26-16 (E1)
P - BR
Air fuel ratio sensor signal
Ignition switch ON
2.9 V*1
E26-24 (HT1B) - E26-53 (E04)
Y - W-B
Heated oxygen sensor heater operation signal
Idling
Below 3.0 V
Ignition switch ON
11 to 14 V
E26-100 (OX1B) - E26-132 (EX1B)
W - R
Heated oxygen sensor signal
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine
Pulse generation
(See waveform 4)
E26-20 (#10) - E26-50 (E01)
B - W-B
No. 1 fuel injector assembly signal
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 5)
E26-17 (#20) - E26-50 (E01)
R - W-B
No. 2 fuel injector assembly signal
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 5)
E26-18 (#30) - E26-50 (E01)
Y - W-B
No. 3 fuel injector assembly signal
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 5)
E26-19 (#40) - E26-50 (E01)
L - W-B
No. 4 fuel injector assembly signal
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 5)
E26-123 (KNK1) - E26-124 (EKNK)
R - G
Knock control sensor signal
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(See waveform 6)
E26-82 (VV1+) - E26-114 (VV1-)
V - L
Camshaft position sensor signal (for intake camshaft)
Idling
Pulse generation
(See waveform 7)
E26-81 (EV1+) - E26-112 (EV1-)
P - W
Camshaft position sensor signal (for exhaust camshaft)
Idling
Pulse generation
(See waveform 7)
E26-76 (NE+) - E26-109 (NE-)
B - W
Crankshaft position sensor signal
Idling
Pulse generation
(See waveform 8)
E26-57 (IGT1) - E26-16 (E1)
Y - BR
No. 1 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 9)
E26-56 (IGT2) - E26-16 (E1)
R - BR
No. 2 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 9)
E26-55 (IGT3) - E26-16 (E1)
G - BR
No. 3 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 9)
E26-54 (IGT4) - E26-16 (E1)
L - BR
No. 4 ignition coil assembly (ignition signal)
Idling
Pulse generation
(See waveform 9)
E26-51 (IGF1) - E26-16 (E1)
W - BR
Ignition coil assembly (ignition confirmation signal)
Ignition switch ON
4.5 to 5.5 V
Idling
Pulse generation
(See waveform 9)
E26-68 (PRG) - E26-50 (E01)
W - W-B
Purge VSV operation signal
Ignition switch ON
11 to 14 V
Idling, under purge control
Pulse generation
(See waveform 10)
A25-57 (SPD) - E26-16 (E1)
L - BR
Vehicle speed signal from combination meter assembly
Driving at 20 km/h (12 mph)
Pulse generation
(See waveform 11)
A25-22 (STA) - E26-16 (E1)
LG - BR
Starter signal
Cranking
5.5 V or higher
E26-63 (NSW) - E26-16 (E1)
LG - BR
Park/neutral position switch assembly signal
Ignition switch ON, shift lever not in P or N
11 to 14 V
Ignition switch ON, shift lever in P or N
Below 3.0 V
A25-11 (STP) - E26-16 (E1)
BE - BR
Stop light switch assembly signal
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
A25-24 (ST1-) - E26-16 (E1)
GR - BR
Stop light switch assembly signal
(opposite to voltage at STP terminal)
Ignition switch ON,
brake pedal depressed
Below 1.5 V
Ignition switch ON,
brake pedal released
7.5 to 14 V
E26-60 (M+) - E26-58 (ME01)
W - W-B
Throttle actuator operation signal (positive terminal)
Idling with warm engine
Pulse generation
(See waveform 12)
E26-30 (M-) - E26-58 (ME01)
B - W-B
Throttle actuator operation signal (negative terminal)
Idling with warm engine
Pulse generation
(See waveform 13)
A25-21 (FC) - E26-50 (E01)
V - W-B
Fuel pump control
Ignition switch ON
11 to 14 V
A25-30 (W) - E26-16 (E1)
LG - BR
Malfunction Indicator Lamp (MIL) operation signal
Ignition switch ON
Below 3.0 V
Idling
11 to 14 V
A25-23 (TC) - E26-16 (E1)
P - BR
Terminal TC of DLC3
Ignition switch ON
11 to 14 V
A25-31 (TACH) - E26-16 (E1)
B - BR
Engine speed
Idling
Pulse generation
(See waveform 14)
A25-7 (VPMP) - E26-50 (E01)
GR - W-B
Vent valve (built into canister pump module)
Ignition switch ON
11 to 14 V
A25-19 (MPMP) - E26-50 (E01)
B - W-B
Leak detection pump (built into canister pump module)
Leak detection pump off
Below 3.0 V
Leak detection pump on
9 to 14 V
E26-113 (VCV1) - E26-16 (E1)
B - BR
Power source of camshaft position sensor (for intake camshaft) (specific voltage)
Ignition switch ON
4.5 to 5.5 V
E26-111 (VCE1) - E26-16 (E1)
LG - BR
Power source of camshaft position sensor (for exhaust camshaft) (specific voltage)
Ignition switch ON
4.5 to 5.5 V
A25-34 (VCPP) - A25-48 (EPPM)
Y - G
Power source of canister pressure sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
A25-49 (PPMP) - A25-48 (EPPM)
B - G
Canister pressure sensor (built into canister pump module)
Ignition switch ON
3.0 to 3.6 V
E26-73 (ALT) - E26-16 (E1)
L - BR
Generator assembly
Ignition switch ON
11 to 14 V
A25-13 (CANH) - E26-16 (E1)
B - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 15)
A25-26 (CANL) - E26-16 (E1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 16)
E26-69 (ACIS) - E26-50 (E01)
P - W-B
Vacuum switching valve for ACIS (Acoustic Control Induction System) operation signal
Ignition switch ON
11 to 14 V
E26-22 (IA1+) - E26-50 (E01)
W - WB
Intake air control valve actuator for tumble control valve
Idling with cold engine
Pulse generation
(See waveform 17)
E26-21 (IA1-) - E26-50 (E01)
G - WB
Intake air control valve actuator for tumble control valve
Idling with cold engine
Pulse generation
(See waveform 18)
E26-131 (IAC1) - E26-129 (EIA1)
B - L
Tumble control valve position sensor
Ignition switch off to ON
3.0 to 4.0 V
E26-130 (VCIA) - E26-16 (E1)
B - BR
Power source of tumble control valve position sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
A25-45 (NEO)*2 - E26-16 (E1)
G - BR
Crankshaft position sensor signal sent to certification ECU (smart key ECU assembly)
Idling with warm engine
Pulse generation
(See waveform 19)
A25-5 (FANL) - E26-50 (E01)
R - W-B
Cooling fan motor operation signal (low)
Ignition switch ON
11 to 14 V
Idling with A/C on, or high engine coolant temperature
Below 1.5 V
A25-6 (FANH) - E26-50 (E01)
W - W-B
Cooling fan motor operation signal (high)
Ignition switch ON
11 to 14 V
Idling with high engine coolant temperature
Below 1.5 V
A25-14 (EC) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
E26-50 (E01) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
E26-49 (E02) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
E26-58 (ME01) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
E26-59 (GE01) - Body ground
G - -
Shielded earth (ground) circuit of throttle actuator
Always
Below 1 Ω
  1. *1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
  2. *2: w/ Smart Key System.

WAVEFORM 1
A093229E38
Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft) Operation Signal 
ECM Terminal Name
Between OC1+ and OC1-
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling

WAVEFORM 2
A093229E11
Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft) Operation Signal 
ECM Terminal Name
Between OE1+ and OE1-
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling

WAVEFORM 3
A205412E01
Air Fuel Ratio Sensor (Sensor 1) Heater Operation Signal 
ECM Terminal Name
Between HA1A and E04
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

HINT:
The wavelength varies in accordance with the engine operating condition.


WAVEFORM 4
A088863E15
Heated Oxygen Sensor (Sensor 2) Signal 
ECM Terminal Name
Between OX1B and EX1B
Tester Range
0.2 V/DIV., 200 ms./DIV.
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:
In the Data List, the item O2S B1S2 shows the values input to the ECM from the heated oxygen sensor.


WAVEFORM 5
A093279E24
No. 1 (to No. 4) Fuel Injector Assembly Signal 
ECM Terminal Name
Between #10 (to #40) and E01
Tester Range
20 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 6
A085286E82
Knock Control Sensor Signal 
ECM Terminal Name
Between KNK1 and EKNK
Tester Range
1 V/DIV., 1 ms./DIV.
Condition
Engine speed maintained at 4000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine speed increases.
  2. The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.


WAVEFORM 7
A255508E10
Camshaft Position Sensor Signal (for Intake and Exhaust Camshaft) 
ECM Terminal Name
CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 8
A254145E02
Crankshaft Position Sensor Signal 
ECM Terminal Name
Between NE+ and NE-
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 9
A122717E29
Ignition Coil Assembly Signal (IGT and IGF Signal) 
ECM Terminal Name
CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 10
A218020E01
Purge VSV Signal 
ECM Terminal Name
Between PRG and E01
Tester Range
10 V/DIV., 20 ms./DIV.
Condition
Idling, under purge control

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 11
A005135E29
Vehicle Speed Signal 
ECM Terminal Name
Between SPD and E1
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Driving at 20 km/h (12 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 12
A208000E03
Throttle Actuator Positive Terminal Signal 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 13
A245848E01
Throttle Actuator Negative Terminal Signal 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 14
A093225E33
Engine Speed Signal 
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 15
A086154E48
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 16
A086155E44
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 17
A093274E49
Positive Terminal of Intake Air Control Valve Actuator (for Tumble Control Valve) Signal 
ECM Terminal Name
Between IA1+ and E01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with cold engine

WAVEFORM 18
A093275E50
Negative Terminal of Intake Air Control Valve Actuator (for Tumble Control Valve) Signal 
ECM Terminal Name
Between IA1- and E01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with cold engine

WAVEFORM 19
A210050E01
Crankshaft Position Sensor Signal 
ECM Terminal Name
Between NEO and E1
Tester Range
5 V/DIV., 2 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine speed increases.