DTC P0112 Intake Air Temperature Circuit Low Input |
DTC P0113 Intake Air Temperature Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0112 | A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| P0113 | An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| Higher than 128°C (262°F) | Short circuit |
| Related DTCs | P0112: Intake air temperature sensor range check (low voltage) P0113: Intake air temperature sensor range check (high voltage) |
| Required Sensors/Components (Main) | Intake air temperature sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| Battery voltage | 8 V or higher |
| Engine switch | On (IG) |
| Starter | Off |
| Intake air temperature sensor voltage [Intake air temperature] | Less than 0.18 V [Higher than 128°C (262°F)] |
| Intake air temperature sensor voltage [Intake air temperature] | Higher than 4.91 V [Less than -55°C (-67°F)] |
| Intake air temperature sensor voltage [Intake air temperature] | 0.18 to 4.91 V [-55 to 128°C (-67 to 262°F)] |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (INTAKE AIR) |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Data List / Primary / Intake Air.
Read the value displayed on the Techstream.
| Result | Proceed to |
| -40°C (-40°F) | A |
| Higher than 128°C (262°F) | B |
| Same as actual intake air temperature | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS) |
Disconnect the mass air flow meter sub-assembly connector.

| *1 | Mass Air Flow Meter Sub-assembly | *2 | ECM |
| *a | Front view of wire harness connector (to Mass Air Flow Meter Sub-assembly) | - | - |
Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter sub-assembly connector on the wire harness side.
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Data List / Primary / Intake Air.
Read the value displayed on the Techstream.
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) |
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E14-1 (THA) - E26-96 (THA) | Always | Below 1 Ω |
| E14-2 (E2) - E26-118 (ETHA) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the mass air flow meter sub-assembly connector.
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Data List / Primary / Intake Air.
Read the value displayed on the Techstream.
| *1 | Mass Air Flow Meter Sub-assembly |
| *2 | ECM |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) |
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E14-1 (THA) or E26-96 (THA) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||