DTC P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction |
DTC P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem |
DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0120 | The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic). |
|
| P0121 | The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or higher than 1.6 V for 2 seconds (1 trip detection logic). |
|
| P0122 | The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic). |
|
| P0123 | The output voltage of VTA1 is 4.54 V or higher for 2 seconds or more (1 trip detection logic). |
|
| P0220 | The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic). |
|
| P0222 | The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic). |
|
| P0223 | The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1 trip detection logic). |
|
| P2135 | Either of the following conditions is met (1 trip detection logic): (a) The difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more. (b) The output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less for 0.4 seconds or more. |
|
| Techstream Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| Throttle Position No. 1 | 0.5 to 1.1 V | 3.2 to 4.8 V |
| Throttle Position No. 2 | 2.1 to 3.1 V | 4.6 to 4.98 V |
| Related DTCs | P0120: Throttle position sensor 1 range check (chattering) P0121: Throttle position sensor rationality P0122: Throttle position sensor 1 range check (low voltage) P0123: Throttle position sensor 1 range check (high voltage) P0220: Throttle position sensor 2 range check (chattering) P0222: Throttle position sensor 2 range check (low voltage) P0223: Throttle position sensor 2 range check (high voltage) P2135: Throttle position sensor range check (correlation) |
| Required Sensors/Components (Main) | Throttle position sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 2 seconds: P0120, P0122, P0123, P0220, P0222 and P0223 Within 2 seconds: P0121 0.5 seconds: P2135 (Case 1) 0.4 seconds: P2135 (Case 2) |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| Either of the following conditions is met | A or B |
| A. Engine switch on (IG) | 0.012 seconds or more |
| B. Electronic throttle actuator power | On |
| Both of the following conditions are met | - |
| Either of the following conditions is met | A or B |
| A. Engine switch | On (IG) |
| B. Electric throttle motor power | On |
| Throttle position sensor circuit fail (P0120, P0122, P0123, P0220, P0222, P0223, P2135) | Not detected |
| VTA1 voltage | 0.2 V or less, or 4.54 V or higher |
| Either of the following conditions is met | A or B |
| A. Difference of learned throttle position sensor opener position voltage between VTA2 and VTA1 | Higher than 1.6 V |
| B. Difference of learned throttle position sensor opener position voltage between VTA2 and VTA1 | Lower than 0.8 V |
| VTA1 voltage | 0.2 V or less |
| VTA1 voltage | 4.54 V or higher |
| Either of the following conditions is met | A or B |
| A. VTA2 voltage | 1.75 V or less |
| B. VTA2 voltage when VTA1 0.2 V to 2.02 V | 4.8 V or higher |
| VTA2 voltage | 1.75 V or less |
| VTA2 voltage when VTA1 0.2 V to 2.02 V | 4.8 V or higher |
| Difference between VTA1 and VTA2 voltages | 0.02 V or less |
| VTA1 voltage | 0.2 V or less |
| VTA2 voltage | 1.75 V or less |
| VTA1 voltage | Higher than 0.2 V, and less than 4.54 V |
| VTA2 voltage | Higher than 1.75 V, and less than 4.8 V |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (THROTTLE POSITION SENSOR) |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Data List / Gas Throttle / Throttle Position No. 1 and Throttle Position No. 2.
Read the values displayed on the Techstream.
| When Accelerator Pedal Fully Released | When Accelerator Pedal Fully Depressed | Trouble Area | Proceed to | ||
| Throttle Position No. 1 (VTA1) | Throttle Position No. 2 (VTA2) | Throttle Position No. 1 (VTA1) | Throttle Position No. 2 (VTA2) | ||
| 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | VCTA circuit open | A |
| 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | ETA circuit open | |
| 0 to 0.2 V, or 4.5 to 4.98 V | 2.1 to 3.1 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 4.98 V | 2.1 to 3.1 V (Fail-safe) | VTA1 circuit open or shorted to ground | |
| 0.6 to 1.4 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 4.98 V | 0.6 to 1.4 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 4.98 V | VTA2 circuit open or shorted to ground | |
| 0.5 to 1.1 V | 2.1 to 3.1 V | 3.2 to 4.8 V (Not fail-safe) | 4.6 to 4.98 V (Not fail-safe) | Throttle position sensor circuit normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
Disconnect the throttle with motor body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E16-5 (VC) - E26-126 (VCTA) | Always | Below 1 Ω |
| E16-6 (VTA) - E26-128 (VTA1) | Always | Below 1 Ω |
| E16-4 (VTA2) - E26-127 (VTA2) | Always | Below 1 Ω |
| E16-3 (E2) - E26-125 (ETA) | Always | Below 1 Ω |
| E16-5 (VC) or E26-126 (VCTA) - Body ground | Always | 10 kΩ or higher |
| E16-6 (VTA) or E26-128 (VTA1) - Body ground | Always | 10 kΩ or higher |
| E16-4 (VTA2) or E26-127 (VTA2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the throttle with motor body assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E16-5 (VC) - E16-3 (E2) | Engine switch on (IG) | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Throttle with Motor Body Assembly) |
|
| ||||
| OK | |
| 4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
Replace the throttle with motor body assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223, and/or P2135 are output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||