Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B278841E04

  1. Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3D-31 (BECU) - Body ground
    V - Body ground
    Battery power supply
    Ignition switch off
    11 to 14 V
    3E-1 - Body ground
    W - Body ground
    Battery power supply
    Ignition switch off
    11 to 14 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3B-7 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    I12-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.



  5. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3D-3 - Body ground
    GR - Body ground
    Front side marker light LH drive output
    Light control switch in tail or head position
    11 to 14 V
    Light control switch off
    Below 1 V
    3D-6 - Body ground
    B - Body ground
    Front side marker light RH drive output
    Light control switch in tail or head position
    11 to 14 V
    Light control switch off
    Below 1 V
    3D-7 - Body ground
    L - Body ground
    Parking light RH drive output
    Light control switch in tail or head position
    11 to 14 V
    Light control switch off
    Below 1 V
    3D-8 - Body ground
    W - Body ground
    Parking light LH drive output
    Light control switch in tail or head position
    11 to 14 V
    Light control switch off
    Below 1 V
    3D-9 - Body ground
    P - Body ground
    Taillight relay drive signal output
    Light control switch in tail or head position
    11 to 14 V
    Light control switch off
    Below 1 V
    3D-12 (HRLY) - Body ground
    P - Body ground
    Headlight relay drive output
    Light control switch in head position
    Below 1 V
    Light control switch not in head position
    11 to 14 V
    3D-20 (PKB) - Body ground
    Y - Body ground
    Parking brake switch input
    Parking brake switch on
    Below 1 V
    Parking brake switch off
    11 to 14 V
    3D-23 (DRL)*1 - Body ground
    P - Body ground
    Daytime running light system drive output
    Daytime running light system operating
    Below 1 V
    Daytime running light system not operating
    11 to 14 V
    3D-38 (FFGO)*2 - Body ground
    P - Body ground
    Front fog light drive output
    Light control switch in head position, front fog light switch on
    Below 1 V
    Light control switch in head position, front fog light switch off
    11 to 14 V
    3D-39 (DIM) - Body ground
    W - Body ground
    High beam headlight drive output
    Dimmer switch in high or high flash position
    Below 1 V
    Dimmer switch in low position
    11 to 14 V
    3C-5 - Body ground
    P - Body ground
    Taillight relay drive signal output
    Light control switch in tail or head position
    11 to 14 V
    Light control switch off
    Below 1 V
    I13-5 (HU) - Body ground
    LG - Body ground
    Dimmer switch high position signal input
    Dimmer switch in high position
    Below 1 V
    Dimmer switch not in high position
    Pulse generation
    I13-8 (HF) - Body ground
    R - Body ground
    Dimmer switch high flash position signal input
    Dimmer switch in high flash position
    Below 1 V
    Dimmer switch not in high flash position
    Pulse generation
    I13-20 (CLTB) - I13-22 (CLTE)
    B - P
    Automatic light control sensor power supply output
    Ignition switch off
    Below 1 V
    Ignition switch ON, light control switch in AUTO position
    11 to 14 V
    I13-21 (CLTS) - Body ground
    G - Body ground
    Automatic light control sensor signal input
    Ignition switch off
    Below 1 V
    Automatic light control system operates
    Pulse generation
    (See waveform 1)
    I13-27 (FFOG)*2 - Body ground
    V - Body ground
    Front fog light switch input
    Front fog light switch on
    Below 1 V
    Front fog light switch off
    Pulse generation
    I13-28 (A) - Body ground
    G - Body ground
    Light control switch AUTO position signal input
    Light control switch in AUTO position
    Below 1 V
    Light control switch not in AUTO position
    Pulse generation
    I13-29 (HEAD) - Body ground
    P - Body ground
    Light control switch head position input
    Light control switch in head position
    Below 1 V
    Light control switch not in head position, ignition switch off
    Pulse generation
    Light control switch not in head position, ignition switch ON
    11 to 14 V
    I13-30 (TAIL) - Body ground
    W - Body ground
    Light control switch tail position signal input
    Light control switch in tail or head position
    Below 1 V
    Light control switch in neither tail nor head position, ignition switch off
    Pulse generation
    Light control switch in neither tail nor head position, ignition switch ON
    11 to 14 V

    1. *1: w/ Daytime Running Light
    2. *2: w/ Front Fog Light
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.



      B113714E01
    1. Waveform 1
      Item
      Content
      Tool setting
      5 V/DIV., 5 ms./DIV.

      HINT:
      If the ambient light becomes brighter, width A becomes narrower.