Home › Audio/Visual/Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM

INTUITIVE PARKING ASSIST SYSTEM > TERMINALS OF ECU

for Preparation Click here



CLEARANCE WARNING ECU ASSEMBLY

E220917E02

  1. Disconnect the I82 connector from the clearance warning ECU assembly.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I82-9 (CLSW) - I82-30 (E)
    B - BR
    Back sonar or clearance sonar switch assembly power source signal
    Engine switch on (IG), clearance sonar main switch on
    11 to 14 V
    I82-9 (CLSW) - I82-30 (E)
    B - BR
    Back sonar or clearance sonar switch assembly power source signal
    Engine switch on (IG), clearance sonar main switch off
    Below 1 V
    I82-1 (IG) - I82-30 (E)
    Y - BR
    IG power source signal
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V
    I82-30 (E) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the I82 connector to the clearance warning ECU assembly.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I82-22 (BOR) - I82-30 (E)
    V - BR
    Power source for rear sensor circuit
    Engine switch off
    Below 1 V
    Engine switch on (IG), clearance sonar main switch on
    7.2 to 8.8 V
    I82-8 (SOF) - I82-30 (E)
    P - BR
    Front sensor communication signal (Front clearance sonar sensor)
    Engine switch on (IG), clearance sonar main switch on, shift lever in R
    Pulse generation
    (See waveform 2)
    I82-13 (ER) - I82-30 (E)
    R - BR
    Clearance warning buzzer signal
    Buzzer sounding
    Pulse generation
    (See waveform 1)
    I82-23 (E1) - I82-30 (E)
    GR - BR
    Ground for rear clearance sonar
    Always
    Below 1 V
    I82-6 (E5) - I82-30 (E)
    W - BR
    Ground for front clearance sonar
    Always
    Below 1 V
    I82-4 (BOF) - I82-30 (E)
    R - BR
    Power source for front sensor circuit
    Engine switch off
    Below 1 V
    Engine switch on (IG), clearance sonar main switch on
    7.2 to 8.8 V
    I82-24 (SOR) - I82-30 (E)
    L - BR
    Rear sensor communication signal (Rear clearance sonar sensor)
    Engine switch on (IG), clearance sonar main switch on, shift lever in R
    Pulse generation
    (See waveform 2)



  5. Using an oscilloscope, check waveform 1.



      E227014E01
    1. Waveform 1 (Reference)
      Item
      Content
      Terminal No. (Symbol)
      I82-13 (ER) - I82-30 (E)
      Tool Setting
      2 V/DIV., 500 μsec./DIV.
      Vehicle Condition
      When sonar detects obstacle (buzzer sounds)
      Buzzer volume
      M2 (Medium volume)

      HINT:
      The amplitude of the waveform changes according to the set volume.



  6. Using an oscilloscope, check waveform 2.



      E231486E01
    1. Waveform 2 (Reference)
      Item
      Content
      Terminal No. (Symbol)
      1. CH: 1 I82-8 (SOF) - I82-30 (E)
      2. CH: 2 I82-24 (SOR) - I82-30 (E)
      Tool Setting
      5 V/DIV., 1 msec./DIV.
      Condition
      Engine switch on (IG), clearance sonar main switch on, shift lever in R

      HINT:
      The waveforms for CH1 and CH2 are same.