Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Key System)

ENGINE IMMOBILISER SYSTEM (w/ Smart Key System) > TERMINALS OF ECU

for Preparation Click here



CHECK ENGINE SWITCH

B271001E05

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I58-6 (AGND) - Body ground
    -
    G - Body ground
    Transponder key amplifier ground
    Always
    Below 1 Ω
    -
    I58-7 (TXCT) - I58-6 (AGND)
    Input
    GR - G
    Immobiliser communication input
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    -
    I58-8 (CODE) - I58-6 (AGND)
    Output
    SB - G
    Immobiliser communication output
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    -
    I58-10 (VC5) - I58-6 (AGND)
    Input
    LG - G
    Transponder key amplifier power supply
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    -

  2. Check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I58-7 (TXCT) - I58-6 (AGND)
    Input
    GR - G
    Signal input from certification ECU (smart key ECU assembly)
    (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
    Pulse generation
    (See waveform 1)
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    5. Frame Error
    6. Response

      HINT:
      If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above

    I58-8 (CODE) - I58-6 (AGND)
    Output
    SB - G
    Signal output to certification ECU (smart key ECU assembly)
    (Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
    Engine switch off, engine switch pressed with key held near engine switch*
    Pulse generation
    (See waveform 2)
    I58-10 (VC5) - I58-6 (AGND)
    Input
    LG - G
    Transponder key amplifier power supply
    (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
    Pulse generation
    (See waveform 3)
    If the result is not as specified, the engine switch may have a malfunction.

    HINT:
    *: Remove the key battery before performing this inspection.



  3. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B051052E14
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I58-7 (TXCT) - I58-6 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch off, key not in cabin, within 30 seconds after engine switch pressed



    2. B251418E01
    3. Waveform 2 (Reference)
      Text in Illustration 
      *a
      Key held against engine switch
      Measurement Condition 
      Item
      Content
      Tester Connection
      I58-8 (CODE) - I58-6 (AGND)
      Tool Setting
      1 V/DIV., 200 ms./DIV.
      Condition
      Engine switch off, engine switch pressed with key held near engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.



    4. B216007E01
    5. Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I58-10 (VC5) - I58-6 (AGND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B264892E28

  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    A43-2 (+B) - A43-11 (E)
    Input
    W - W
    +B power supply
    Always
    11 to 14 V
    -
    A43-10 (CUTB) - A43-11 (E)
    Input
    L - W
    Dark current cut pin
    Always
    11 to 14 V
    -
    A43-11 (E) - Body ground
    -
    W - Body ground
    Ground
    Always
    Below 1 Ω
    -

  3. Reconnect the A43 certification ECU (smart key ECU assembly) connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I78-5 (IG) - A43-11 (E)
    Input
    LG - W
    Ignition power supply
    Engine switch off → on (IG)
    Below 1 V → 11 to 14 V
    Ignition Switch
    I78-18 (IND) - A43-11 (E)
    Output
    L - W
    Security indicator output
    Engine switch off → on (IG)
    Pulse generation
    → Below 2 V
    -
    I78-9 (TXCT) - I78-24 (AGND)
    Output
    GR - G
    Signal output to transponder key amplifier
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    5. Frame Error
    6. Response
    I78-7 (CODE) - I78-24 (AGND)
    Input
    SB - G
    Signal input from transponder key amplifier
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    I78-1 (VC5) - I78-24 (AGND)
    Output
    LG - G
    Transponder key amplifier power supply
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V
    I78-24 (AGND) - Body ground
    -
    G - Body ground
    Transponder key amplifier ground
    Always
    Below 1 Ω
    A43-14 (EFII) - A43-11 (E)
    Input
    SB - W
    EFI communication input
    (Signal input from ECM to certification ECU (smart key ECU assembly))
    Engine switch off
    11 to 14 V
    1. B2799
    2. B279A
    3. Engine Start Request
    4. EFI Code Receive
    A43-13 (EFIO) - A43-11 (E)
    Output
    Y - W
    EFI communication output
    (Signal output from certification ECU (smart key ECU assembly) to ECM)
    Engine switch off
    Below 1 V

  5. Check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I78-9 (TXCT) - I78-24 (AGND)
    Output
    GR - G
    Signal output to transponder key amplifier
    (Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
    Pulse generation
    (See waveform 1)
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    5. Frame Error
    6. Response
    I78-7 (CODE) - I78-24 (AGND)
    Input
    SB - G
    Signal input from transponder key amplifier
    (Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
    Engine switch off, engine switch pressed with key held near engine switch*
    Pulse generation
    (See waveform 2)
    I78-1 (VC5) - I78-24 (AGND)
    Output
    LG - G
    Transponder key amplifier power supply
    (Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
    Pulse generation
    (See waveform 3)
    A43-14 (EFII) - A43-11 (E)
    Input
    SB - W
    EFI communication input
    (Signal input from ECM to certification ECU (smart key ECU assembly))
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    Pulse generation
    (See waveform 4)
    1. B2799
    2. B279A
    3. Engine Start Request
    4. EFI Code Receive
    A43-13 (EFIO) - A43-11 (E)
    Output
    Y - W
    EFI communication output
    (Signal output from certification ECU (smart key ECU assembly) to ECM)
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    Pulse generation
    (See waveform 5)
    If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.

    HINT:
    *: Remove the key battery before performing this inspection.



  6. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B051052E14
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I78-9 (TXCT) - I78-24 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Engine switch off, key not in cabin, within 30 seconds after engine switch pressed



    2. B251418E01
    3. Waveform 2 (Reference)
      Text in Illustration 
      *a
      Key held against engine switch
      Measurement Condition 
      Item
      Content
      Tester Connection
      I78-7 (CODE) - I78-24 (AGND)
      Tool Setting
      1 V/DIV., 200 ms./DIV.
      Condition
      Engine switch off, engine switch pressed with key held near engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.



    4. B216007E01
    5. Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      I78-1 (VC5) - I78-24 (AGND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      Engine switch off, key not in cabin, within 30 seconds after engine switch pressed



    6. Waveform 4 (Reference)


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      A43-14 (EFII) - A43-11 (E)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected



    7. Waveform 5 (Reference)


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      A43-13 (EFIO) - A43-11 (E)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

B118684E75

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    I24-1 (GND) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    I24-3 (IGE) - I24-1 (GND)
    Input
    SB - W-B
    Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly))
    Steering lock motor operates when both conditions met, and then door opened:
    1. Shift lever in P
    2. Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off
    Pulse generation
    (See waveform 1)
    1. Power Supply Short
    2. Unlock Request Receive
    3. Lock Request Receive
    I24-4 (SLP1) - I24-1 (GND)
    Output
    P - W-B
    Steering lock bar position signal (signal output from steering unlock sensor)
    Steering locked → unlocked*1
    11 to 14 V → Below 1.2 V
    1. Push Start Error
    2. Sensor Value
    I24-6 (IG2) - I24-1 (GND)
    Input
    LG - W-B
    IG signal (IG2 power supply input for steering lock motor)
    Engine switch off → on (IG)
    Below 1 V → 11 to 14 V
    1. B2788
    2. Ignition Switch
    I24-7 (B) - Body ground
    Output
    B - Body ground
    Constant power supply
    Always
    11 to 14 V
    B2788
    If the result is not as specified, the steering lock ECU (steering lock actuator assembly) may have a malfunction.

    HINT:
    *1: The steering locks when any door is opened with the shift lever in P and the engine switch off. The steering unlocks when the engine switch is turned on (ACC).



  2. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      C221561E01
    1. Waveform 1 (Reference)
      Text in Illustration 
      *a
      Steering lock motor not operating
      *b
      Steering lock motor operating
      Measurement Condition 
      Item
      Content
      Tester Connection
      I24-3 (IGE) - I24-1 (GND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Steering lock motor operates when both conditions met, and then door opened:
      1. Shift lever in P
      2. Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off


CHECK ECM

A247842E31

HINT:
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


for 2GR-FE 
Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
E26-49 (E1) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
A25-1 (BATT) - E26-49 (E1)
Input
GR - BR
+B power supply
Always
11 to 14 V
-
A25-2 (+B) - E26-49 (E1)
Input
P - BR
+B power supply
Engine switch on (IG)
11 to 14 V
-
A25-3 (+B2) - E26-49 (E1)
Input
LG - BR
+B power supply
Engine switch on (IG)
11 to 14 V
-
A25-30 (IMO) - E26-49 (E1)
Input
SB - BR
Certification ECU (smart key ECU assembly) communication input
Engine switch off
11 to 14 V
-
A25-30 (IMO) - E26-49 (E1)
Input
SB - BR
Certification ECU (smart key ECU assembly) communication input
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
Pulse generation
(See waveform 1)
-
A25-31 (IMI) - E26-49 (E1)
Output
Y - BR
Certification ECU (smart key ECU assembly) communication output
Engine switch off
Below 1 V
-
A25-31 (IMI) - E26-49 (E1)
Output
Y - BR
Certification ECU (smart key ECU assembly) communication output
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
Pulse generation
(See waveform 2)
-

for 2AR-FE 
Terminal No. (Symbol)
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item/DTC
E26-16 (E1) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
A25-1 (BATT) - E26-16 (E1)
Input
GR - BR
+B power supply
Always
11 to 14 V
-
A25-2 (+B) - E26-16 (E1)
Input
P - BR
+B power supply
Engine switch on (IG)
11 to 14 V
-
A25-3 (+B2) - E26-16 (E1)
Input
LG - BR
+B power supply
Engine switch on (IG)
11 to 14 V
-
A25-29 (IMO) - E26-16 (E1)
Input
SB - BR
Certification ECU (smart key ECU assembly) communication input
Engine switch off
11 to 14 V
-
A25-29 (IMO) - E26-16 (E1)
Input
SB - BR
Certification ECU (smart key ECU assembly) communication input
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
Pulse generation
(See waveform 1)
-
A25-28 (IMI) - E26-16 (E1)
Output
Y - BR
Certification ECU (smart key ECU assembly) communication output
Engine switch off
Below 1 V
-
A25-28 (IMI) - E26-16 (E1)
Output
Y - BR
Certification ECU (smart key ECU assembly) communication output
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
Pulse generation
(See waveform 2)
-


  1. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




    1. Waveform 1 (Reference)


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      A25-30 (IMO) - E26-49 (E1)*1
      A25-29 (IMO) - E26-16 (E1)*2
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
      1. *1: for 2GR-FE
      2. *2: for 2AR-FE



    2. Waveform 2 (Reference)


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      A25-31 (IMI) - E26-49 (E1)*1
      A25-28 (IMI) - E26-16 (E1)*2
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
      1. *1: for 2GR-FE
      2. *2: for 2AR-FE