ENGINE UNIT > REASSEMBLY |
| 1. INSTALL ENGINE REAR OIL SEAL |
Place the oil seal retainer on wooden blocks.
![]() |
Using SST, tap in a new engine rear oil seal until its surface is flush with the engine rear oil seal retainer edge.
| *a | Depth |
| 2. INSTALL ENGINE REAR OIL SEAL RETAINER |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
| *a | Seal Packing Diameter (2.0 to 3.0 mm (0.0787 to 0.118 in.)) |
![]() |
Install the engine rear oil seal retainer with the 6 bolts.
| 3. INSTALL WATER INLET PIPE |
![]() |
Install the water inlet pipe with the 2 bolts.
Install the No. 1 water by-pass hose.
| 4. INSTALL CYLINDER HEAD GASKET RH |
![]() |
Place a new cylinder head gasket RH on the cylinder block surface with the Lot No. stamp facing upward.
| *a | Lot No. |
![]() | Engine Front |
| 5. INSTALL CYLINDER HEAD SUB-ASSEMBLY RH |
Place the cylinder head on the cylinder block.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
Step 1
![]() |
Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps and in the sequence shown in the illustration.
![]() |
Step 2
| *a | Turn 90° |
| *b | Painted Mark |
![]() | Engine Front |
Mark each cylinder head bolt head with paint as shown in the illustration.
Tighten the cylinder head bolts 90° in the sequence shown in step 1.
Step 3
Tighten the cylinder head bolts an additional 90° in the sequence shown in step 1.
Check that the painted mark is now facing rearward.
| 6. INSTALL CYLINDER HEAD GASKET LH |
![]() |
Place a new cylinder head gasket LH on the cylinder block surface with the Lot No. stamp facing upward.
| *a | Lot No. |
![]() | Engine Front |
| 7. INSTALL CYLINDER HEAD SUB-ASSEMBLY LH |
Place the cylinder head on the cylinder block.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
Step 1
![]() |
Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.
![]() |
Step 2
| *a | Turn 90° |
| *b | Painted Mark |
![]() | Engine Front |
Mark each cylinder head bolt head with paint as shown in the illustration.
Tighten the cylinder head bolts 90° in the sequence shown in step 1.
Step 3
Tighten the cylinder head bolts an additional 90° in the sequence shown in step 1.
Check that the painted mark is now facing rearward.
![]() |
Tighten the 2 bolts in the order shown in the illustration.
| 8. INSTALL VALVE STEM CAP |
Install the 24 valve stem caps.
| 9. INSTALL VALVE LASH ADJUSTER ASSEMBLY |
Place the lash adjuster into a container filled with engine oil.
![]() |
Insert the tip of SST into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.
| *1 | Tapered Part |
| *2 | Plunger |
| *3 | Check Ball |
| *a | CORRECT |
| *b | INCORRECT |
| *c | Low Pressure Chamber |
| *d | High Pressure Chamber |
Squeeze SST and lash adjuster together to move the plunger up and down 5 to 6 times.
Check the movement of the plunger and bleed the air.
After bleeding the air, remove SST. Then, try to press the plunger quickly and firmly by hand.
Install the valve lash adjusters.
| 10. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
Apply engine oil to the lash adjuster tip and valve stem cap end.
![]() |
Install the valve rocker arms as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Lash Adjuster |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
| 11. INSTALL NO. 3 CAMSHAFT |
Apply a light coat of engine oil to the No. 3 camshaft journals and camshaft housing sub-assembly LH.
Install the No. 3 camshaft to the camshaft housing sub-assembly LH.
| 12. INSTALL NO. 4 CAMSHAFT |
Apply a light coat of engine oil to the No. 4 camshaft journals and camshaft housing sub-assembly LH.
Install the No. 4 camshaft to the camshaft housing sub-assembly LH.
| 13. INSTALL CAMSHAFT BEARING CAP (for Bank 2) |
Apply engine oil to the camshaft bearing caps.
![]() |
Make sure of the marks and numbers on the camshaft bearing caps and place them in each proper position and direction.
![]() |
Temporarily tighten the 8 bolts in the order shown in the illustration.
| 14. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH |
![]() |
Make sure that the valve rocker arm is installed as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Lash Adjuster |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
| *a | Seal packing diameter (3.5 to 4.5 mm) |
![]() |
Install the camshaft housing sub-assembly LH and tighten the 13 bolts in the order shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
![]() |
Tighten the 8 bolts in the order shown in the illustration.
| 15. INSTALL CAMSHAFT |
Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly RH.
Install the camshaft to the camshaft housing sub-assembly RH.
| 16. INSTALL NO. 2 CAMSHAFT |
Apply a light coat of engine oil to the No. 2 camshaft journals and camshaft housing sub-assembly RH.
Install the No. 2 camshaft to the camshaft housing sub-assembly RH.
| 17. INSTALL CAMSHAFT BEARING CAP (for Bank 1) |
Apply engine oil to the camshaft bearing caps.
![]() |
Make sure of the marks and numbers on the camshaft bearing caps and place them in each proper position and direction.
![]() |
Temporarily tighten the 8 bearing cap bolts in the order shown in the illustration.
| 18. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH |
![]() |
Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Lash Adjuster |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
| *a | Seal packing diameter (3.5 to 4.5 mm) |
![]() |
Install the camshaft housing sub-assembly RH and tighten the 12 bolts in the order shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
![]() |
Tighten the 8 bolts in the order shown in the illustration.
| 19. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Install the No. 3 chain tensioner assembly with the bolt.
| *1 | Plunger |
| *2 | Pin |
| *a | Push |
While pushing in the tensioner, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold it.
| 20. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2) |
![]() |
Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.
| *1 | Timing Mark |
| *2 | Mark Plate |
Apply a light coat of engine oil to the bolt threads and bolt-seating surface.
Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly installed.
![]() |
Using SST to hold the hexagonal portion of each camshaft, tighten the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Remove the pin from the No. 3 chain tensioner assembly.
| 21. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Install the No. 2 chain tensioner assembly with the bolt.
| *1 | Plunger |
| *2 | Pin |
| *a | Push |
While pushing in the No. 2 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold it.
| 22. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1) |
![]() |
Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.
| *1 | Timing Mark |
| *2 | Mark Plate |
Apply a light coat of engine oil to the bolt threads and bolt-seating surface.
Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly installed.
![]() |
Using SST to hold the hexagonal portion of each camshaft, tighten the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Remove the pin from the No. 2 chain tensioner assembly.
| 23. INSTALL NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Install the No. 1 chain vibration damper with the 2 bolts.
| 24. INSTALL NO. 2 CHAIN VIBRATION DAMPER |
Install the 2 No. 2 chain vibration dampers.
| 25. INSTALL CRANKSHAFT TIMING SPROCKET |
![]() |
Install the 2 keys and crankshaft timing sprocket as shown in the illustration.
| 26. INSTALL IDLE SPROCKET ASSEMBLY |
![]() |
Apply a light coat of engine oil to the rotating surface of the No. 1 idle gear shaft.
| *1 | Knock Pin |
Temporarily install the No. 1 idle gear shaft and idle sprocket with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block.
Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.
| 27. INSTALL CHAIN SUB-ASSEMBLY |
![]() |
Align the mark plates and timing marks as shown in the illustration and install the chain.
| *1 | Mark Plate |
| *a | Timing Mark |
![]() |
Do not pass the chain over the crankshaft, just temporarily place it on the crankshaft.
![]() |
Turn the camshaft timing gear assembly on bank 1 counterclockwise to tighten the chain between the banks.
| *1 | Mark Plate |
| *a | Turn |
| *b | When the idle sprocket is reused |
| *c | Mark |
| *d | Align |
![]() |
Align the mark plate and timing marks as shown in the illustration and install the chain onto the crankshaft timing sprocket.
| *1 | Mark Plate |
| *a | Timing Mark |
Temporarily tighten the pulley set bolt.
![]() |
Turn the crankshaft clockwise to set it to the RH block bore center line (TDC/compression).
| *1 | Center Line |
| *2 | Timing Mark |
| *3 | Sensor Plate |
| 28. INSTALL CHAIN TENSIONER SLIPPER |
Install the chain tensioner slipper.
| 29. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
| *1 | Stopper Plate |
| *2 | Plunger |
Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.
![]() |
Install the No. 1 chain tensioner assembly with the 2 bolts.
Remove the hexagon wrench from the No. 1 chain tensioner assembly.
| 30. INSPECT VALVE TIMING |
Check the camshaft timing marks.
Check that each camshaft timing mark is positioned as shown in the illustration.

| *a | Timing Mark | *b | Viewpoint |
![]() |
If the valve timing is misaligned, reinstall the timing chain.
Remove the pulley set bolt.
| 31. INSTALL TIMING CHAIN CASE OIL SEAL |
![]() |
Using SST, tap in a new oil seal until its surface is flush with the timing chain case edge.
Apply a light coat of MP grease to the timing chain cover oil seal lip.
| 32. INSTALL ENGINE WATER PUMP ASSEMBLY |
![]() |
Install a new water pump gasket and the engine water pump assembly with the 8 bolts.
| 33. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY |
Apply seal packing in a continuous line to the engine unit as shown in the following illustration.

| *a | Seal Diameter: 3.0 mm or more | ![]() | Seal Packing |
Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

| *a | Dashed line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) | *b | Continuous line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) |
| *c | Alternate long and short dashed line area (Seal packing: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent) | *d | Diagonal line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) |
![]() | Be sure to apply seal packing | - | - |
| Area | Seal Packing Diameter | Application Position from Inside Seal Line |
| Continuous Line Area | 4.5 mm or more (0.177 in.) | 1.0 to 2.0 mm (0.0394 to 0.0787 in.) |
| Alternate Long and Short Dashed Line Area | 3.5 mm or more (0.138 in.) | 2.0 to 3.0 mm (0.0787 to 0.118 in.) |
| Dashed Line Area | 3.5 mm or more (0.138 in.) | 3.0 to 4.0 mm (0.118 to 0.158 in.) |
| Diagonal Line Area | 6.0 mm or more (0.236 in.) | 5.0 mm (0.197 in.) |
![]() |
Install a new gasket.
![]() |
Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.
| *1 | Drive Rotor Spline |
| *2 | Crankshaft |
![]() |
Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.
| *1 | Nut |
| Item | Length |
| Bolt A | 40 mm (1.57 in.) |
| Bolt B | 55 mm (2.17 in.) |
| Bolt C | 25 mm (0.984 in.) |
![]() |
Fully tighten the bolts in this order: Area 1 and Area 2.
| *a | Area 1 |
| *b | Area 2 |
| *c | Area 3 |
| *d | Area 4 |
Fully tighten the bolts and nuts in Area 3.
Fully tighten the bolts in Area 4.
Install a new timing chain cover plate gasket and the timing chain cover plate with the 4 bolts.
| 34. INSTALL WATER INLET HOUSING |
![]() |
Install 2 new O-rings.
![]() |
Install the 2 stud bolts.
![]() |
Install the water inlet housing with the 2 bolts and nut.
| *1 | Nut |
| *2 | Bolt |
Connect the No. 1 water by-pass hose.
Apply adhesive around the drain cock.
Install the drain cock assembly to the water inlet housing.
Install the drain cock plug to the drain cock assembly.
Install a new gasket to the thermostat.
![]() |
Align the thermostat jiggle valve with the upper stud bolt, and insert the thermostat in the water inlet housing.
![]() |
Install the water inlet with the 2 nuts.
| 35. INSTALL NO. 1 FRONT ENGINE MOUNTING BRACKET LH |
![]() |
Using an E8 "TORX" socket wrench, install the 2 stud bolts.
| *1 | Stud Bolt |
Install the No. 1 front engine mounting bracket LH with the 6 bolts.
| 36. INSTALL NO. 1 OIL PAN BAFFLE PLATE |
![]() |
Install the No. 1 oil pan baffle plate with the 7 bolts.
| 37. INSTALL OIL PAN SUB-ASSEMBLY |
Using an E8 "TORX" socket wrench, install the 2 stud bolts.

| *a | Timing Chain Cover | *b | Lower Cylinder Block |
![]() |
Install 2 new O-rings.
![]() |
Apply seal packing in a continuous line as shown in the illustration.
| *a | Seal Diameter |
![]() |
Install the oil pan with the 16 bolts and 2 nuts.
| *1 | Nut |
| 38. INSTALL OIL STRAINER SUB-ASSEMBLY |
![]() |
Using an E6 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.
| *a | Timing Chain Cover |
![]() |
Install a new gasket and the oil strainer sub-assembly with the bolt and 2 nuts.
| *1 | Nut |
| 39. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Using an E6 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.
![]() |
Apply seal packing in a continuous line as shown in the illustration.
| *a | Seal Diameter |
![]() |
Install the No. 2 oil pan sub-assembly with the 16 bolts and 2 nuts.
| *1 | Nut |
| 40. INSTALL OIL PAN DRAIN PLUG |
![]() |
Install a new oil pan drain plug gasket and the oil pan drain plug.
| 41. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Apply seal packing as shown in the illustration.
![]() | Seal Packing |
![]() |
Install 3 new gaskets as shown in the illustration.
Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.
![]() |
Install the head cover with the 12 bolts and a new seal washer.
| 42. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH |
![]() |
Apply seal packing as shown in the illustration.
![]() | Seal Packing |
![]() |
Install 3 new gaskets as shown in the illustration.
Install a new No. 2 cylinder head cover gasket to the cylinder head cover sub-assembly LH.
![]() |
Install the cylinder head cover sub-assembly LH with the 12 bolts and a new seal washer.
| 43. INSTALL WATER OUTLET |
![]() |
Install 2 new gaskets and a new O-ring.
![]() |
Install the water outlet with the 2 bolts and 4 nuts.
| *1 | Nut |
| *2 | Bolt |
| 44. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE |
![]() |
Apply a light coat of engine oil to a new O-ring and install it to the engine oil level dipstick guide.
![]() |
Install the engine oil level dipstick guide with the bolt.
| 45. INSTALL CRANKSHAFT PULLEY |
Align the pulley set key with the key groove of the pulley, and slide on the pulley.
![]() |
Using SST, install the pulley bolt.
| *a | Hold |
![]() | Turn |
| 46. INSTALL OIL FILTER CAP ASSEMBLY |
Clean the inside of the oil filter cap, threads and O-ring groove.
![]() |
Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.
| *1 | Oil Filter Element |
| *2 | Oil Filter Cap |
| *3 | O-ring |
Install a new oil filter element to the oil filter cap.
Remove all dirt and foreign matter from the installation surface and the inside of the cap on the engine side.
Apply a light coat of engine oil to the O-ring again and install the oil filter cap.
![]() |
Using SST, install the oil filter cap.
| *a | No Clearance |
![]() |
Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.
| *1 | O-ring |
Install the oil filter drain plug to the oil filter cap.
| 47. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
![]() |
Apply adhesive around the drain cock sub-assembly.
| *1 | Adhesive |
![]() |
Install the water drain cocks as shown in the illustration.
| *a | for Bank 1 |
| *b | for Bank 2 |
Install the water drain cock plugs to the water drain cocks.
| 48. INSTALL NO. 1 OIL PIPE |
Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.
![]() |
Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side) with the union.
| *1 | Oil Pipe Union |
Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the union.
Tighten the oil pipe union (on the head cover side).
Tighten the oil pipe union (on the cylinder head side).
| 49. INSTALL OIL PIPE |
Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.
![]() |
Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side) with the union.
| *1 | Oil Pipe Union |
Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the union.
Install the bolt (A) to the cylinder head.
Tighten the oil pipe union (on the head cover side).
Tighten the oil pipe union (on the cylinder head side).
| 50. INSTALL CRANK POSITION SENSOR |
![]() |
Apply a light coat of engine oil to the O-ring on the crank position sensor.
| *1 | O-ring |
Install the crank position sensor with the bolt.
Connect the crank position sensor connector.
| 51. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Apply a light coat of engine oil to 4 new O-rings and install them to the 4 camshaft timing oil control valve assemblies.
| *1 | New O-ring |
Install the 4 oil control valves with the 4 bolts.
Connect the 4 oil control valve connectors.
| 52. INSTALL VVT SENSOR |
Install the 4 sensors with the 4 bolts.
Connect the 4 sensor connectors.
| 53. INSTALL VENTILATION VALVE SUB-ASSEMBLY |
Apply adhesive around the ventilation valve sub-assembly.
![]() |
Using a deep socket wrench 19 mm, install the ventilation valve sub-assembly.
| 54. INSTALL SPARK PLUG |
![]() |
Install the 6 spark plugs.
| 55. INSTALL OIL FILLER CAP SUB-ASSEMBLY |
Install a new oil filler gasket.
Install the oil filler cap sub-assembly.