DTC P0505 Idle Control System Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0505 | Idle speed continues to vary greatly from target idle speed (2 trip detection logic). |
|

| Related DTCs | P0505: Idle air control system functional check |
| Required Sensors/Components (Main) | Electronic throttle control system |
| Required Sensors/Components (Related) | Crankshaft position sensor Engine coolant temperature sensor Vehicle speed sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 minutes |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | P0010, P0020 (Camshaft timing oil control valve bank 1, 2) P0011, P0021 (VVT system bank 1, 2 - advance) P0012, P0022 (VVT system bank 1, 2 - retard) P0013, P0023 (Exhaust camshaft timing oil control valve bank 1, 2) P0014, P0024 (Exhaust VVT system bank 1, 2 - advance) P0015, P0025 (Exhaust VVT system bank 1, 2 - retard) P0016, P0018 (VVT system bank 1, 2 - misalignment) P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor) P0171, P0172, P0174, P0175 (Fuel system) P0301, P0302, P0303, P0304, P0305, P0306 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351, P0352, P0353, P0354, P0355, P0356 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0451, P0452, P0453 (EVAP system) P0500 (Vehicle speed sensor) P0705 (Shift lever position switch) P219A, P219B (Air-fuel ratio imbalance) |
| Engine | Running |
| Either of the following conditions are met | 1 or 2 |
| 1. Both of the following conditions are met | - |
| Engine speed - Target engine speed | Less than -100 rpm, or higher than 200 rpm (A/C on or NSW on) Less than -100 rpm, or higher than 150 rpm (A/C off and NSW off) |
| IAC flow rate learned value | 0.88 L/sec. or less, or 8.5 L/sec. or more for 5 seconds or more |
| 2. Both of the following conditions are met | A and B |
| A. Frequency that both of the following conditions are met | 5 times or more |
| Engine speed - Target engine speed | Less than -100 rpm, or higher than 200 rpm (A/C on or NSW on) Less than -100 rpm, or higher than 150 rpm (A/C off and NSW off) |
| Vehicle condition | Stopped after vehicle was driven by 10 km/h (6.25 mph) or higher |
| B. Either of the following condition is met | (a) or (b) |
| (a) Amount of change of IAC flow rate learning value | +4.04 L/sec. or more, or -7.52 L/sec. or less |
| (b) IAC flow rate learning value | 0.88 L/sec. or less, or 8.5 L/sec. or more |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505) |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0505 is output | A |
| DTC P0505 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 3.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE) |
Check the throttle with motor body assembly condition.
|
| ||||
| OK | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0505) |
Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
| DTC P0505 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||