Home › Drivetrain · U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0617    Starter Relay Circuit High

for Preparation Click here


DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the TCM.
If the TCM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The TCM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) for over 20 seconds.

DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more applied to TCM for 20 seconds
(1 trip detection logic):
(a) Vehicle speed more than 20 km/h (12.43 mph)
(b) Engine speed more than 1000 rpm
(c) STA signal ON
  1. Park/Neutral Position switch
  2. Starter relay circuit
  3. Cranking holding function circuit
  4. TCM

MONITOR STRATEGY


Related DTCs
P0617: Starter signal
Required Sensors/Components (Main)
STARTER relay, PNP switch, engine switch
Required Sensors/Components (Sub)
Vehicle speed sensor (VSS), Crankshaft Position (CKP) sensor
Frequency of Operation
Continuous
Duration
20 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever these DTCs are not present:
None
Battery voltage
10.5 V or more
Vehicle speed
12.43 mph (20 km/h) or more
Engine speed
1,000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS


Starter signal
ON

WIRING DIAGRAM


C240539E01


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine does not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the Techstream. The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).

1.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / ECT / Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Starter Signal
    Starter signal/
    Open or Close
    Open: Starter operating
    Close: Starter not operating
    -

  1. Crank the engine.

  1. Read the value displayed on the Techstream.

    OK:
    Tester Display
    Condition
    Specified Condition
    Starter Signal
    Engine switch on (IG)
    Close
    Starter Signal
    Engine is cranking
    Open



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    A107908E94
  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E4-4 (B) - E4-9 (L)
    P
    Below 1 Ω
    N
    Below 1 Ω
    Except P and N
    10 kΩ or higher
    E4-1 (RB) - E4-9 (L)
    P
    10 kΩ or higher
    R
    10 kΩ or higher
    N
    10 kΩ or higher
    D
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Park/Neutral Position Switch)



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (TCM - PARK/NEUTRAL POSITION SWITCH)


    C189544E68
  1. Disconnect the TCM connector.

  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E7-10 (STA) - Body ground
    Engine switch on (IG)
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to TCM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / ECT/ Trouble Codes.

  1. Read the DTCs.

    Result: 
    Result
    Proceed to
    DTC is not output
    OK
    DTC P0617 is output
    NG



NG
REPLACE TCM (Click here)
OK

END