SLIDING ROOF SYSTEM > Sliding Roof does not Move by Operating Sliding Roof Control Switch |

| 1.READ VALUE USING TECHSTREAM |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Sliding Roof / Data List.
Read the Data List according to the display on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Open Switch | OPEN switch signal/ON or OFF | ON: OPEN switch pressed OFF: OPEN switch not pressed | - |
| Close Switch | CLOSE switch signal/ON or OFF | ON: CLOSE switch pressed OFF: CLOSE switch not pressed | - |
| Up Switch | UP switch signal/ON or OFF | ON: UP switch pressed OFF: UP switch not pressed | - |
| Down Switch | DOWN switch signal/ON or OFF | ON: DOWN switch pressed OFF: DOWN switch not pressed | - |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY AND BODY GROUND) |
Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S4-8 (B) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S4-12 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 3.INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX ASSEMBLY) |
![]() |
Remove the sliding roof switch (roof console box assembly) (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (UP) - 1 (GND) | UP switch is pressed | Below 1 Ω |
| 5 (UP) - 1 (GND) | UP switch is not pressed | 10 kΩ or higher |
| 4 (DOWN) - 1 (GND) | DOWN switch is pressed | Below 1 Ω |
| 4 (DOWN) - 1 (GND) | DOWN switch is not pressed | 10 kΩ or higher |
| 3 (OPN) - 1 (GND) | OPEN switch is pressed | Below 1 Ω |
| 3 (OPN) - 1 (GND) | OPEN switch is not pressed | 10 kΩ or higher |
| 2 (CLS) - 1 (GND) | CLOSE switch is pressed | Below 1 Ω |
| 2 (CLS) - 1 (GND) | CLOSE switch is not pressed | 10 kΩ or higher |
| *a | Component without harness connected (Sliding Roof Switch (Roof Console Box Assembly)) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH AND BODY GROUND) |
Disconnect the S12 sliding roof switch (roof console box assembly) connector.
Disconnect the S4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S4-5 (CLS) - S12-2 (CLS) | Always | Below 1 Ω |
| S4-5 (CLS) - Body ground | Always | 10 kΩ or higher |
| S4-7 (OPN) - S12-3 (OPN) | Always | Below 1 Ω |
| S4-7 (OPN) - Body ground | Always | 10 kΩ or higher |
| S4-6 (DWN) - S12-4 (DOWN) | Always | Below 1 Ω |
| S4-6 (DWN) - Body ground | Always | 10 kΩ or higher |
| S4-4 (UP) - S12-5 (UP) | Always | Below 1 Ω |
| S4-4 (UP) - Body ground | Always | 10 kΩ or higher |
| S12-1 (GND) - Body ground | Always | Below 1 Ω |
| S4-12 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||