Home › Drivetrain ยท U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

    HINT:
    1. To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
    2. When you select a measurement group, the ECU data belonging to that group is displayed.
    3. Measurement Group List / Description
      1. All Data / All data
      2. Primary / -
      3. Engine Control / Engine control system related data
      4. Gas General / -
      5. Gas AF Control / Air fuel ratio control system related data
      6. Gas AF O2 Sensor / Air fuel ratio sensor and heated oxygen sensor related data
      7. Gas Throttle / Gasoline throttle system related data
      8. Gas Intake Control / Intake control system related data
      9. Gas Valve Control / Valve control system related data
      10. Gas Misfire / "Misfire" related data
      11. Gas Starting / "Difficult to start" related data
      12. Gas Rough Idle / "Rough idle" related data
      13. Gas Evaporative / Evaporative system related data
      14. Gas CAT Converter / Catalyst converter related data
      15. Check Mode / Check mode related data
      16. Monitor Status / Monitor status related data
      17. Ignition / Ignition system related data
      18. Charging Control / Charging control system related data
      19. Compression / Data used during "Check the Cylinder Compression" Active Test
      20. AT / Automatic transmission system related data
      21. Vehicle Information / Vehicle information

  7. According to the display on the Techstream, read the Data List.

    HINT:
    1. The title used for each group of Data List items in this repair manual does not appear on the Techstream. However, the name in parentheses after the title, which is a Measurement Group, does appear on the Techstream. When the name shown in parentheses is selected on the Techstream, all the Data List items listed for that group will be displayed.
    2. "Result of real-vehicle check" is the assessment of one vehicle. Use it only for reference.


    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed /
    Min.: 0 km/h (0 MPH), Max.: 255 km/h (158 MPH)
    Actual vehicle speed
    -
    Engine Speed
    Engine speed /
    Min.: 0 rpm, Max.: 16383.75 rpm
    600 to 700 rpm: Idling
    When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
    Calculate Load
    Calculated load /
    Min.: 0.0%, Max.: 100.0%
    1. Ignition switch ON: 0.0%
    2. Idling (engine warmed up): 28.2%
    3. Running without load (3000 rpm): 26.2%
    4. Vehicle driven at constant speed of 60 km/h (37 mph): 56.8%
    This is the engine load calculated based on the estimated intake manifold pressure.
    Calculate Load = Estimated intake manifold pressure / maximum intake manifold pressure x 100 (%)
    (For example, when the estimated intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.)
    Coolant Temp
    Engine coolant temperature /
    Min.: -40 C (-40 F), Max.: 140 C (284 F)
    75 to 100°C (176 to 221°F): After warming up
    1. If value -40°C (-40°F): sensor circuit open
    2. If value 140°C (284°F): sensor circuit shorted
    Engine Run Time
    Engine run time /
    Min.: 0 S
    Max.: 65535 S
    Time after engine start
    This is the time elapsed since the engine started.

    HINT:
    The time is counted only while the engine is running.

    Battery Voltage
    Battery voltage /
    Min.: 0, Max.: 65.535 V
    11 to 14 V: Idling
    -
    Throttle Sensor Volt %
    Throttle position sensor output/
    Min.: 0%, Max.: 100%
    10 to 22%: Idling
    Calculated value based on VTA1
    Throttle Sensor Position
    Throttle sensor position/
    Min.: 0%, Max.: 100%
    1. 0%: Accelerator pedal fully released
    2. 50 to 80%: Accelerator pedal fully depressed
    This is the throttle valve opening amount used for engine control.
    (100% signifies 125° of throttle valve rotation. This does not include the amount the throttle valve is opened to maintain the idle speed during idling.)
    This value has no meaning when the ignition switch is ON and the engine is stopped.
    The throttle valve opening amount during idling is indicated by 0%. When the throttle valve is fully open, the value is 68%.
    Starter Signal
    Starter signal/
    Open or Close
    -
    -
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    1. ON: Shift lever is in P or N
    2. OFF: Shift lever is not in P or N
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    Stop Light Switch
    Stop light switch status/
    ON or OFF
    Brake pedal is
    1. ON: Depressed
    2. OFF: Released
    -
    TC terminal
    TC Terminal Status /
    ON or OFF
    -
    -
    #Codes (Include History)
    # of Codes /
    Min.: 0, Max.: 255
    -
    Number of detected DTCs
    MIL ON Run Distance
    MIL ON run distance /
    Min.: 0 km (0 mile),
    Max.: 65535 km (40723 mile)
    Distance after DTC detected
    -
    Running Time from MIL ON
    Running time from MIL ON /
    Min.: 0 min,
    Max.: 65535 min,
    Equivalent to running time after MIL ON
    -
    Time after DTC Cleared
    Time after DTC cleared /
    Min.: 0 min,
    Max.: 65535 min,
    Equivalent to time after DTCs cleared
    -
    Distance from DTC Cleared
    Distance after DTC cleared /
    Min.: 0 km (0 mile)
    Max.: 65535 km (40723 mile)
    Equivalent to time after DTCs cleared
    -
    Warmup Cycle Cleared DTC
    Warm-up cycle after DTC cleared /
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after DTCs cleared
    TC and TE1
    TC and TE1 terminals of DLC3 /
    ON or OFF
    -
    Active Test support data
    Transmission Type2
    [NA]
    -
    -
    SPD (NT)
    Input turbine speed/
    Min.: 0 rpm, Max.: 12750 rpm
    Lock-up is
    1. ON (After warming up the engine):
      Input turbine speed (NT) is equal to engine speed
    2. OFF (idling with shift lever in N):
      Input turbine speed (NT) is nearly equal to engine speed
    Data is displayed in increments of 50 rpm
    SPD (NC)
    Counter gear speed /
    Min.: 0 rpm, Max.: 12750 rpm
    -
    Data is displayed in increments of 50 rpm
    Shift SW Status (P Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever is in P
    2. OFF: Shift lever is not in P
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here

    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever is in R
    2. OFF: Shift lever is not in R
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here

    Shift SW Status (N Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever is in N
    2. OFF: Shift lever is not in N
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here

    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Continuously shift to "+" (up-shift)
    2. OFF: Release "+" (up-shift)
    -
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Continuously shift to "-" (down-shift)
    2. OFF: Release "-" (down-shift)
    -
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    Shift lever is:
    1. ON: S, "+" or "-"
    2. OFF: Not in S, "+" or "-"
    -
    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    1. ON: Shift lever is in D or S
    2. OFF: Shift lever is not in D or S
    When the shift lever position displayed on the Techstream differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here

    A/T Oil Temperature 1
    ATF temp. sensor value/
    min.: -40 C (-40 F)
    max.: 215 C (419 F)
    1. After stall test;
      Approx. 80°C (176°F)
    2. Equal to ambient temperature when cold soak
    If the value is "-40°C (-40°F)" or "150°C (302°F)", ATF temp. sensor circuit is open or shorted.
    NT Sensor Voltage
    Input speed sensor NT output voltage /
    Min.: 0.000 V, Max.: 5.000 V
    0.1 to 1.9 V
    -
    NC Sensor Voltage
    Output speed sensor NC output voltage /
    Min.: 0.000 V, Max.: 5.000 V
    0.1 to 1.9 V
    -
    Lock Up
    Lock up /
    0: OFF / 1: ON
    Lock up: ON
    -
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd, 4th, 5th or 6th
    Same as actual gear
    -
    SLT Solenoid Status
    Shift solenoid SLT status/
    ON or OFF
    Shift solenoid SLT is
    1. Operating: ON
    2. Not operating: OFF
    -
    SLU Solenoid Status
    Shift Solenoid SLU Status/
    ON or OFF
    Shift solenoid SLU is
    1. Operating: ON
    2. Not operating: OFF
    -
    SL Solenoid Status
    Shift Solenoid SL Status/
    ON or OFF
    Shift solenoid SL is
    1. Operating: ON
    2. Not operating: OFF
    -
    AT Fluid
    Flex lockup judder judgment flag /
    0: OFF / 1: ON
    -
    -


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the Techstream, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Connect the TC and TE1
    Connects and disconnects TC and TE1.
    (transitions into the fluid temperature detection mode)
    ON/OFF
    The MIL will not blink when "Connect the TC and TE1 / ON" is selected.
    Activate the Solenoid (SLU)
    Operates shift solenoid SLU
    ON/OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SLT)*
    Operates shift solenoid SLT to raise the line pressure.
    ON/OFF

    HINT:
    ON: No action (normal operation)
    OFF: Line pressure up (When the Active Test of "Activate the Solenoid (SLT)" is performed, the ECM commands the SLT solenoid to turn off).

    [Vehicle Condition]
    1. Vehicle Stopped
    2. IDL: ON
    Activate the Lock Up
    Controls the shift solenoid SLU and SL to set the automatic transaxle to the lock-up condition.
    ON/OFF
    Can be used to check SLU and SL solenoid operation.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 20%
    2. Vehicle speed:60 km/h (37 mph) or more, and 6th gear
    Activate the Solenoid (SL)
    Operates shift solenoid SL
    ON/OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Control the Shift Position
    Operates the shift solenoid valves to allow gears to selected manually.
    1. Press "→" button: Upshift occurs
    2. Press "←" button: Downshift occurs
    Can be used to check the operation of the shift solenoid valves.
    Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.
    Do not downshift at high speeds. Doing so will damage the automatic transaxle.
    [Vehicle Condition]
    1. 50 km/h (31 mph) or less
    Activate the Solenoid (SL1)
    Operates shift solenoid SL1
    ON/OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL2)
    Operates shift solenoid SL2
    ON/OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL3)
    Operates shift solenoid SL3
    ON/OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL4)
    Operates shift solenoid SL4
    ON/OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    *: The "Activate the solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test (Click here).

    HINT:
    Note that the pressure readings for the Active Test and Hydraulic Test are different.