Home › Drivetrain · U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P2716    Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

for Preparation Click here


DESCRIPTION

Refer to the system description for DTC P2714 .

DTC No.
DTC Detection Condition
Trouble Area
P2716
Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1-trip detection logic).
  1. Open or short in shift solenoid valve SLT circuit
  2. Shift solenoid valve SLT
  3. Wiring harness connector
  4. ECM

MONITOR DESCRIPTION

When an open or short in the linear solenoid valve (SLT) circuit is detected, the ECM interprets this as a fault. The ECM will turn on the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P2716: Shift solenoid valve SLT/Range check
Required sensors/Components
Shift solenoid valve SLT
Frequency of operation
Continuous
Duration
1 sec.
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


ALL: 
The monitor will run whenever this DTC is not present
None
Solenoid current cut status
Not cut
Ignition switch
ON
Starter
OFF

Malfunction (A): 
Battery voltage
12 V or more
Target current
1 A

Malfunction (B): 
Battery voltage
10 V or more and less than 12 V
Target current
0.75 A

Malfunction (C): 
Battery voltage
8 V or more
Target current
1 A

Malfunction (D): 
Battery voltage
11 V or more
Target current
1 A or more

Malfunction (E): 
Battery voltage
11 V or more
Target current
0.1 A or more
Commanded voltage - Last commanded voltage
Less than 0.000019 V

TYPICAL MALFUNCTION THRESHOLDS


Malfunction (A) and (B): 
Output duty cycle
100% or more

Malfunction (C): 
Output duty cycle
0% or less

Malfunction (D): 
Output signal monitor
No signal

Malfunction (E): 
Commanded voltage - Average of monitor voltage
0.035 V or more

COMPONENT OPERATING RANGE


Output duty cycle
Less than 100%

WIRING DIAGRAM


C239277E01


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SLT CIRCUIT)


    C233488E01
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    E26-15 (SLT+) - E26-14 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    E26-15 (SLT+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E26-14 (SLT-) - Body ground and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
Go to step 2
OK

REPLACE ECM (Click here)  

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
  1. Disconnect the harness connector from the wiring harness connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    E26-15 (SLT+) - E8-15 (SLT+)
    Always
    Below 1 Ω
    E26-14 (SLT-) - E8-7 (SLT-)
    Always
    Below 1 Ω
    E26-15 (SLT+) or E8-15 (SLT+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E26-14 (SLT-) or E8-7 (SLT-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT TRANSMISSION WIRE (SLT)


    C133212E37
  1. Remove the wiring harness connector from the transaxle.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-12 (SLT+) - A-7 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    A-12 (SLT+) - Body ground and other terminals
    Always
    10 kΩ or higher
    A-7 (SLT-) - Body ground and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 4
OK

REPLACE WIRING HARNESS CONNECTOR (Click here)  

4.INSPECT SHIFT SOLENOID VALVE SLT


    C201747E01
  1. Remove shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

    OK:
    Valve moves and makes an operating sound.

    Text in Illustration 
    *1
    Shift Solenoid Valve SLT



NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)