Home › Drivetrain · U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P2716    Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

for Preparation Click here


DESCRIPTION

Refer to the system description for DTC P2714 .

DTC No.
DTC Detection Condition
Trouble Area
P2716
Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1-trip detection logic).
  1. Open or short in shift solenoid valve SLT circuit
  2. Shift solenoid valve SLT
  3. TCM

MONITOR DESCRIPTION

When an open or short in the linear solenoid valve (SLT) circuit is detected, the TCM interprets this as a fault. The TCM will turn on the MIL and store the DTC.

MONITOR STRATEGY


Related DTCs
P2716: Shift solenoid valve SLT/Range check
Required sensors/Components
Shift solenoid valve SLT
Frequency of operation
Continuous
Duration
1 sec.
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


ALL: 
The monitor will run whenever this DTC is not present
None
Solenoid current cut status
Not cut
Engine switch
on (IG)
Starter
OFF

Malfunction (A): 
Battery voltage
12 V or more
Target current
1 A

Malfunction (B): 
Battery voltage
10 V or more and less than 12 V
Target current
0.75 A

Malfunction (C): 
Battery voltage
8 V or more
Target current
1 A

Malfunction (D): 
Battery voltage
11 V or more
Target current
1 A or more

Malfunction (E): 
Battery voltage
11 V or more
Target current
0.1 A or more
Commanded voltage - Last commanded voltage
Less than 0.000019 V

TYPICAL MALFUNCTION THRESHOLDS


Malfunction (A) and (B): 
Output duty cycle
100% or more

Malfunction (C): 
Output duty cycle
0% or less

Malfunction (D): 
Output signal monitor
No signal

Malfunction (E): 
Commanded voltage - Average of monitor voltage
0.035 V or more

COMPONENT OPERATING RANGE


Output duty cycle
Less than 100%

WIRING DIAGRAM


C133261E34


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.INSPECT TRANSMISSION WIRE (SLT)


    C133212E58
  1. Remove the TCM from the transaxle.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    12 (SLT+) - 7 (SLT-)
    20°C (68°F)
    5.0 to 5.6 Ω
    12 (SLT+) - Body ground and other terminals
    Always
    10 kΩ or higher
    7 (SLT-) - Body ground and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 2
OK

REPLACE TCM (Click here)  

2.INSPECT SHIFT SOLENOID VALVE SLT


    C201747E01
  1. Remove shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

    Text in Illustration 
    *1
    Shift Solenoid Valve SLT

  1. Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

    OK:
    Valve moves and makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SLT (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)