DTC P0748 Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0748 | The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting between 4th and 5th gears. (1-trip detection logic)
|
|
| Related DTCs | P0748: Shift solenoid valve SL1/Range check |
| Required sensors/Components | Shift solenoid valve SL1 |
| Frequency of operation | Continuous |
| Duration | 1 sec. |
| MIL operation | Immediate |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | None |
| Ignition switch | ON |
| Starter | OFF |
| Battery voltage | 12 V or more |
| Battery voltage | 10 V or more and less than 12 V |
| Target current | Less than 0.75 A |
| Battery voltage | 8 V or more |
| Target current | 0.6 A or more |
| Output duty cycle | 100% or more |
| Output duty cycle | 0% or less |
| Output duty cycle | More than 0% and less than 100% |

| ECM commanded gear | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Shift solenoid valve SL1 | ON | ON | ON | ON | OFF | OFF |
| 1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL1 CIRCUIT) |
![]() |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E26-5 (SL1+) - E26-4 (SL1-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| E26-5 (SL1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| E26-4 (SL1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR) |
Disconnect the harness connector from the wiring harness connector.
Measure the resistance according to the value(s) in the table below.
| Tester Condition | Condition | Specified Condition |
| E26-5 (SL1+) - E8-17 (SL1+) | Always | Below 1 Ω |
| E26-4 (SL1-) - E8-16 (SL1-) | Always | Below 1 Ω |
| E26-5 (SL1+) or E8-17 (SL1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| E26-4 (SL1-) or E8-16 (SL1-) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION WIRE (SL1) |
![]() |
Remove the wiring harness connector from the transaxle.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A-14 (SL1+) - A-13 (SL1-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| A-14 (SL1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| A-13 (SL1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| *a | Component without harness connected (Transmission Wire) |
|
| ||||
| OK | ||
| ||
| 4.INSPECT SHIFT SOLENOID VALVE SL1 |
![]() |
Remove shift solenoid valve SL1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.
| *1 | Shift Solenoid Valve SL1 |
|
| ||||
| OK | ||
| ||