Home › Drivetrain · U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0748    Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1)

for Preparation Click here


DESCRIPTION

Changing from 1st to 6th is performed by the TCM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated (Click here).

DTC No.
DTC Detection Condition
Trouble Area
P0748
The TCM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting between 4th and 5th gears. (1-trip detection logic)
  1. Output signal duty equals 100%.
    (NOTE: SL1 output signal duty is less than 100% under normal condition.)
  1. Open or short in shift solenoid valve SL1 circuit
  2. Shift solenoid valve SL1
  3. TCM

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL1 circuit. The TCM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem and illuminates the MIL and stores the DTC. The TCM also performs the fail-safe function and turns the other normal shift solenoid valves on or off. (In case of an open or short circuit, the TCM stops sending current to the circuit.)
While driving and shifting between 4th and 5th gears, if the TCM detects an open or short in the shift solenoid valve SL1 circuit, the TCM determines there is a malfunction (Click here).

MONITOR STRATEGY


Related DTCs
P0748: Shift solenoid valve SL1/Range check
Required sensors/Components
Shift solenoid valve SL1
Frequency of operation
Continuous
Duration
1 sec.
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
None
Engine switch
on (IG)
Starter
OFF

Condition (A) 
Battery voltage
12 V or more

Condition (B) 
Battery voltage
10 V or more and less than 12 V
CPU commanded duty
Less than 75%

TYPICAL MALFUNCTION THRESHOLDS


Condition (A) and (B) 
Output duty cycle
100% or more

COMPONENT OPERATING RANGE


Output duty cycle
More than 3% and less than 100%

WIRING DIAGRAM


C133261E33


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


HINT:
The following table shows normal operation of the shift solenoid valve SL1 when the shift lever is in D:

TCM commanded gear
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve SL1
ON
ON
ON
ON
OFF
OFF

1.INSPECT TRANSMISSION WIRE (SL1)


    C133212E52
  1. Remove the TCM from the transaxle.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    14 (SL1+) - 13 (SL1-)
    20°C (68°F)
    5.0 to 5.6 Ω
    14 (SL1+) - Body ground and other terminals
    Always
    10 kΩ or higher
    13 (SL1-) - Body ground and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 2
OK

REPLACE TCM (Click here)  

2.INSPECT SHIFT SOLENOID VALVE SL1
C201747E01
  1. Remove shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

    Text in Illustration 
    *1
    Shift Solenoid Valve SL1

  1. Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

    OK:
    Valve moves and makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SL1 (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)