SMART KEY SYSTEM (for Start Function) > TERMINALS OF ECU |
| CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |

Disconnect the I78 and A43 connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
| A43-7 (STA) - Body ground | Input | V - Body ground | When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is"being started". | 20°C (68°F) | 93.75 to 136.36 Ω | - |
| A43-5 (STAR) - Body ground | Input/Output | P - Body ground | Outputs voltage to the starter relay
| Shift lever in any position other than P or N → shift lever in P or N (at 20°C (68°F)) | 10 kΩ or higher → 93.75 to 136.36 Ω | - |
Receives neutral start switch (P, N position detection) signal
| Perform the following operations except while the engine is cranking:
| 30 kΩ or higher → 93.75 to 136.36 Ω | Neutral SW/ Clutch SW | |||
| A43-16 (NE) - Body ground | Input | G - Body ground | Engine speed signal | Always | 10 kΩ or higher | Engine Condition |
| A43-9 (IG2D) - Body ground | Output | R - Body ground | IG2 signal | 20°C (68°F) | Approximately 302.97 Ω | IG2 Relay Monitor(Outside) |
| A43-18 (STP1) - Body ground | Input | V - Body ground | Stop light switch signal | Brake pedal released → Brake pedal depressed | 9 V or higher → 1 V or less | Stop Light Switch1 |
| A43-2 (+B) - A43-11 (E) | Input | W - W | Power source | Always | 11 to 14 V | - |
| I78-26 (SLP) - A43-11 (E) | Input | P - W | Steering lock position signal | Always | 10 kΩ or higher | Steering Unlock Switch |
| A43-11 (E) - Body ground | - | W - Body ground | GND | Always | Below 1 Ω | - |
| I78-30 (SSW2) - Body ground | Input | V - Body ground | SSW2 contact signal
| Engine switch pushed → Engine switch not pushed | Below 1 Ω → 10 kΩ or higher | Start Switch2 |
| I78-28 (SSW1) - Body ground | Input | R - Body ground | SSW1 contact signal | Engine switch pushed → Engine switch not pushed | Below 1 Ω → 10 kΩ or higher | Start Switch1 |
| I78-4 (ACCD) - Body ground | Output | W - Body ground | ACC signal | 20°C (68°F) | 81.49 to 118.98 Ω | ACC Relay Monitor |
| I78-6 (IG1D) - Body ground | Output | P - Body ground | IG1 signal | 20°C (68°F) | 40.74 to 59.49 Ω | IG1 Relay Monitor(Outside) |
| A43-10 (CUTB) - A43-11 (E) | Input | L - W | Dark current cut pin* | Always | 11 to 14 V | - |
| I78-27 (SPD) - Body ground | Input | V - Body ground | Vehicle speed signal | Always | 30 kΩ or higher | Vehicle Speed Signal |
Reconnect the F63 and F65 connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
| A43-7 (STA) - A43-11 (E) | Input | V - W | When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is"being started". | With the brake pedal depressed, the engine switch is pressed and held (starter on) → After approx. 1 sec. has elapsed, the engine switch is released (starter off) | 6 V or higher*1 → 1.5 V or less | - |
| A43-5 (STAR) - A43-11 (E) | Input/Output | P - W | Outputs voltage to the starter relay
| With the brake pedal depressed, the engine switch is pressed and held → After approx. 1 sec. has elapsed, the engine switch is released | 6 V or higher*1 → 1.5 V or less | - |
Receives neutral start switch (P, N position detection) signal
| Perform the following operations except while the engine is cranking:
| 9 V or higher → 2.7 V or less | Neutral SW/ Clutch SW | |||
| A43-16 (NE) - A43-11 (E) | Input | G - W | Engine speed signal | Idling (engine warmed up) | Pulse generation (See waveform 1) | Engine Condition |
| A43-9 (IG2D) - A43-11 (E) | Output | R - W | IG2 signal | Engine switch on (ACC) → Engine switch on (IG) | 1 V or less → 9 V or higher | IG2 Relay Monitor(Outside) |
| A43-18 (STP1) - A43-11 (E) | Input | V - W | Stop light switch signal | Brake pedal released → Brake pedal depressed | 1 V or less → 9 V or higher | Stop Light Switch1 |
| I78-26 (SLP) - A43-11 (E) | Input | P - W | Steering lock position signal | Steering wheel locked → Steering wheel unlocked*2 | 11 to 14 V → 1.2 V or less | Steering Unlock Switch |
| I78-29 (SLR+) - A43-11 (E) | Output | SB - W | Steering lock motor operation command signal (Steering lock motor operation permission signal sent from the certification ECU (smart key ECU assembly)) | Steering lock motor stopped → Steering lock motor operating → Steering lock motor stopped*3 | Pulse generation (See waveform 2) | - |
| I78-25 (P) - A43-11 (E) | Input | R - W | P position signal | Shift lever in P → Shift lever not in P | 9 V or higher → 1.5 V or less | Shift P Signal |
| I78-30 (SSW2) - A43-11 (E) | Input | V - W | SSW2 contact signal
| Engine switch not pushed → Engine switch pushed | 9 V or higher → 1 V or less | Start Switch2 |
| I78-28 (SSW1) - A43-11 (E) | Input | R - W | SSW1 contact signal | Engine switch not pushed → Engine switch pushed | 9 V or higher → 1 V or less | Start Switch1 |
| I78-4 (ACCD) - A43-11 (E) | Output | W - W | ACC signal | Engine switch off → Engine switch on (ACC) | 1 V or less → 8.5 V or higher | ACC Relay Monitor |
| I78-6 (IG1D) - A43-11 (E) | Output | P - W | IG1 signal | Engine switch on (ACC) → Engine switch on (IG) | 1 V or less → 9 V or higher | IG1 Relay Monitor(Outside) |
| I78-27 (SPD) - A43-11 (E) | Input | V - W | Vehicle speed signal | Vehicle being driven at approx. 5 km/h (3 mph) | Pulse generation (See waveform 3) | Vehicle Speed Signal |
Using an oscilloscope, check the waveform of the ECU.
![]() |
Waveform 1
| Item | Content |
| Tester Connection | A43-16 (NE) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 2 ms./DIV. |
| Vehicle Condition | Idling (engine warmed up) |
![]() |
Waveform 2
| Item | Content |
| Tester Connection | I78-29 (SLR+) - A43-11 (E) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Steering lock motor stopped → Steering lock motor operating → Steering lock motor stopped |
| *a | Steering lock motor not operating |
| *b | Steering lock motor operating |
![]() |
Waveform 3
| Item | Content |
| Tester Connection | I78-27 (SPD) - A43-11 (E) |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle Condition | Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph) |