Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1434    Steering Angle Sensor Output Malfunction

for Preparation Click here


DESCRIPTION

The skid control ECU receives signals from the steering angle sensor via the CAN communication system.

HINT:
If there is trouble in the bus lines between the steering angle sensor and the CAN communication system, DTC U0126 (Lost Communication with Steering Angle Sensor Module) is output. When U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0126 first.

DTCs may be stored if one of the following occurs:
  1. Steering angle sensor zero point value malfunction.
  2. Steering angle sensor signal malfunction.
  3. Steering angle sensor signal stuck malfunction.
  4. Steering angle sensor and the yaw rate sensor values inconsistent.
  5. Steering angle sensor installation abnormality.

DTC No.
DTC Detection Condition
Trouble Area
C1434
Any of the following is detected:
  1. The difference between zero point stored in the steering angle sensor and the estimated zero point exceeds 15 deg.
  2. The offset value of the steering angle sensor is -13.5 deg. or less or 13.5 deg. or more.
  3. The steering angle sensor value exceeds a specified value for 0.3 seconds or more.
  4. The change of the steering angle sensor value within 0.02 seconds is abnormal.
  5. The steering angle sensor value changes by less than 5 deg. and both left and right turns have been recognized.
  6. There is a difference between the skid control ECU estimated value and the steering angle sensor value due to an abnormal steering angle sensor value.
  1. Sensor installation
  2. Steering angle sensor power supply
  3. Steering angle sensor
  4. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM


C167662E39


INSPECTION PROCEDURE

HINT:
  1. When U0073, U0123 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0123 and/or U0126 first (Click here).
  2. When any of the speed sensors, yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) is malfunctioning, DTCs for the steering angle sensor may be stored even though the steering angle sensor is normal. When DTCs for the speed sensors, yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor, yaw rate and acceleration sensor (for separate type) and/ or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) first, and then inspect and repair the steering angle sensor.

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON again and check that no CAN communication system DTC is output (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left and then check that no speed sensor or yaw rate and acceleration sensor DTCs are output (Click here).

    Result:

    Result
    Proceed to
    No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output.
    A
    CAN communication system DTC is output.
    B
    Speed sensor and/or yaw rate and acceleration sensor DTC is output.
    C

    HINT:
    1. If there is a malfunction in any of the speed sensors, yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type), DTCs for the steering angle sensor may be stored even though the steering angle sensor is normal.
    2. If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair the sensors and then inspect the steering angle sensor.



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)

C
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2.CHECK STEERING ANGLE SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. Check that the steering angle sensor has been installed properly (Click here).

    OK:
    The steering angle sensor installation are normal.



NG
INSTALL STEERING ANGLE SENSOR CORRECTLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C156493E40
  1. Remove the steering wheel and the column cover.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the steering angle sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I29-5 (BAT) - Body ground
    Always
    11 to 14 V
    I29-4 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)


    C156493E41
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I29-1 (ESS) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Angle Sensor)

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)
OK

REPLACE STEERING ANGLE SENSOR (Click here)