Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. Turn the ignition switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.
  3. Turn the ignition switch off before inspecting CAN bus lines for a ground short.
  4. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  5. This section describes the standard values for all CAN related components.

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


CAN NO. 1 JUNCTION CONNECTOR


  1. Check the CAN No. 1 junction connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.




    1. Connection diagram


      C256305E01


      Text in Illustration 
      *a
      Component with harness connected
      (CAN No. 1 Junction Connector)
      *b
      to Yaw Rate Sensor*4
      (for V bus)
      *c
      to Main Body ECU (Multiplex Network Body ECU)
      (for V bus)
      *d
      to Steering Sensor
      (for V bus)
      *e
      to Airbag Sensor Assembly
      (for V bus)
      *f
      to DLC3
      *g
      1. to Power Steering ECU with Motor Assembly*1
      2. to Power Steering ECU Assembly*2*3
      (for V bus)
      *h
      to Combination Meter Assembly
      (for V bus)
      *i
      to CAN No. 2 Junction Connector
      (for V bus)
      -
      -
      1. *1: for 2AR-FE w/ Wireless door lock system
      2. *2: for 2AR-FE w/o Wireless door lock system
      3. *3: for 2GR-FE w/ Wireless door lock system
      4. *4: Separate type yaw rate sensor

    2. Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to (Applicable Bus)
      I173-1 (CANH)
      BE
      Yaw Rate Sensor*4
      (for V bus)
      I173-2 (CANL)
      W
      I95-1 (CANH)
      P
      Main body ECU (Multiplex network body ECU)
      (for V bus)
      I95-2 (CANL)
      W
      I97-1 (CANH)
      V
      Steering sensor
      (for V bus)
      I97-2 (CANL)
      W
      I103-1 (CANH)
      Y
      Airbag sensor assembly
      (for V bus)
      I103-2 (CANL)
      W
      I96-1 (CANH)
      L
      DLC3
      I96-2 (CANL)
      W
      I100-1 (CANH)
      G
      1. Power Steering ECU with Motor Assembly*1
      2. Power steering ECU assembly*2*3
      (for V bus)
      I100-2 (CANL)
      W
      I94-1 (CANH)
      R
      Combination meter assembly
      (for V bus)
      I94-2 (CANL)
      W
      I93-1 (CANH)
      B
      CAN No. 2 junction connector
      (for V bus)
      I93-2 (CANL)
      W

      1. *1: for 2AR-FE w/ Wireless door lock system
      2. *2: for 2AR-FE w/o Wireless door lock system
      3. *3: for 2GR-FE w/ Wireless door lock system
      4. *4: Separate type yaw rate sensor


CAN NO. 2 JUNCTION CONNECTOR


  1. Check the CAN No. 2 junction connector.

    HINT:
    Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.




    1. Connection diagram


      C239444E01


      Text in Illustration 
      *a
      Component with harness connected
      (CAN No. 2 Junction Connector)
      *b
      to Clearance Warning ECU Assembly*1
      (for V bus)
      *c
      to ECM
      (for V bus)
      *d
      to Air Conditioning Amplifier Assembly
      (for V bus)
      *e
      to Brake Actuator Assembly (Skid Control ECU)
      (for V bus)
      *f
      to Smart Key ECU Assembly (Certification ECU)*2
      (for V bus)
      *g
      to Network Gateway ECU*3
      (for V bus)
      *h
      1. to Navigation ECU Sub-assembly*4*5
      2. to Radio and Display Receiver Assembly*6
      (for V bus)
      *i
      to CAN No. 1 Junction Connector
      (for V bus)
      -
      -
      1. *1: w/ Intuitive parking assist system
      2. *2: w/ Smart key system
      3. *3: w/ Blind spot monitor system
      4. *4: for Navigation receiver type (for navigation receiver type)
      5. *5: for Navigation receiver type (for radio and display type w/ intuitive parking assist system)
      6. *6: for Radio and display type (for radio and display type w/o intuitive parking assist system)

    2. Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      I111-1 (CANH)
      BE
      Clearance warning ECU assembly*1
      (for V bus)
      I111-2 (CANL)
      W
      I104-1 (CANH)
      P
      ECM
      (for V bus)
      I104-2 (CANL)
      W
      I102-1 (CANH)
      V
      Air conditioning amplifier assembly
      (for V bus)
      I102-2 (CANL)
      W
      I105-1 (CANH)
      Y
      Brake Actuator Assembly (Skid Control ECU)
      (for V bus)
      I105-2 (CANL)
      W
      I106-1 (CANH)
      L
      Smart key ECU assembly (Certification ECU)*2
      (for V bus)
      I106-2 (CANL)
      W
      I108-1 (CANH)
      G
      Network Gateway ECU*3
      (for V bus)
      I108-2 (CANL)
      W
      I107-1 (CANH)
      R
      1. Navigation ECU Sub-assembly*4*5
      2. Radio and Display Receiver Assembly*6
      (for V bus)
      I107-2 (CANL)
      W
      I101-1 (CANH)
      B
      CAN No. 1 junction connector
      (for V bus)
      I101-2 (CANL)
      W

      1. *1: w/ Intuitive parking assist system
      2. *2: w/ Smart key system
      3. *3: w/ Blind spot monitor system
      4. *4: for Navigation receiver type (for navigation receiver type)
      5. *5: for Navigation receiver type (for radio and display type w/ intuitive parking assist system)
      6. *6: for Radio and display type (for radio and display type w/o intuitive parking assist system)


CAN NO. 3 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)


  1. Check the CAN No. 3 junction connector.



      C238890E20
    1. Connection diagram
      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN No. 3 Junction Connector)
      *b
      to Blind Spot Monitor Sensor RH
      (for Sub bus 2)
      *c
      to CAN No. 4 Junction Connector
      (for Sub bus 2)
      *d
      to Network Gateway ECU
      (for Sub bus 2)

    2. Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      O30-9 (CANH)
      R
      Blind Spot Monitor Sensor RH
      (for Sub bus 2)
      O30-20 (CANL)
      B
      O30-10 (CANH)
      G
      CAN No. 4 junction connector
      (for Sub bus 2)
      O30-21 (CANL)
      B
      O30-11 (CANH)
      V
      Network Gateway ECU
      (for Sub bus 2)
      O30-22 (CANL)
      B


CAN NO. 4 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)


  1. Check the CAN No. 4 junction connector.



      C238890E21
    1. Connection diagram
      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN No. 4 Junction Connector)
      *b
      to CAN No. 5 Junction Connector
      (for Sub bus 2)
      *c
      to Blind Spot Monitor Sensor LH
      (for Sub bus 2)
      *d
      to CAN No. 3 Junction Connector
      (for Sub bus 2)

    2. Check the connection diagram of the components which are connected to the CAN No. 4 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      T15-9 (CANH)
      L
      CAN No. 5 junction connector
      (for Sub bus 2)
      T15-20 (CANL)
      B
      T15-10 (CANH)
      R
      Blind Spot Monitor Sensor LH
      (for Sub bus 2)
      T15-21 (CANL)
      B
      T15-11 (CANH)
      G
      CAN No. 3 junction connector
      (for Sub bus 2)
      T15-22 (CANL)
      B


CAN NO. 5 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)


  1. Check the CAN No. 5 junction connector.



      C183982E23
    1. Connection diagram
      Text in Illustration 
      *a
      Rear view of wire harness connector
      (to CAN No. 5 junction connector)
      *b
      to CAN No. 4 Junction Connector
      (for Sub bus 2)

    2. Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      T16-3 (CANH)
      L
      CAN No. 4 junction connector
      (for Sub bus 2)
      T16-2 (CANL)
      B


DLC3
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Measure the resistance according to the value(s) in the table below.


    C188081E20


    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    L - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I39-6 (CANH) - I39-4 (CG)
    L - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I39-14 (CANL) - I39-4 (CG)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I39-6 (CANH) - I39-16 (BAT)
    L - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I39-14 (CANL) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


    Text in Illustration 
    *1
    DLC3
    -
    -


ECM (for 2GR-FE)

A247842E32


Text in Illustration 
*a
Component without harness connected
(ECM)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the ECM connectors.


    C239445E09


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A25-13 (CANH) - A25-26 (CANL)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    A25-13 (CANH) - E26-49 (E1)
    B - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A25-26 (CANL) - E26-49 (E1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A25-13 (CANH) - A25-1 (BATT)
    B - GR
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A25-26 (CANL) - A25-1 (BATT)
    W - GR
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


ECM (for 2AR-FE)

A247842E32


Text in Illustration 
*a
Component without harness connected
(ECM)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the ECM connectors.


    C239445E10


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A25-13 (CANH) - A25-26 (CANL)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    A25-13 (CANH) - E26-16 (E1)
    B - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A25-26 (CANL) - E26-16 (E1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A25-13 (CANH) - A25-1 (BATT)
    B - GR
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A25-26 (CANL) - A25-1 (BATT)
    W - GR
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


COMBINATION METER ASSEMBLY

E224288E07


Text in Illustration 
*a
Component without harness connected
(Combination Meter Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. E224284E21
  3. Disconnect the combination meter assembly connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I18-16 (CANH) - I18-15 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    I18-16 (CANH) - I18-6 (EP)
    R - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I18-15 (CANL) - I18-6 (EP)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I18-16 (CANH) - I18-1 (B)
    R - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I18-15 (CANL) - I18-1 (B)
    W - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B278841E26


Text in Illustration 
*a
Component without harness connected
(Main Body ECU (Multiplex Network Body ECU)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the main body ECU (multiplex network body ECU) connectors.


    C240931E04


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Main Body ECU (Multiplex Network Body ECU))
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I13-14 (CANH) - I13-13 (CANL)
    P - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I13-14 (CANH) - I39-4 (CG)
    P - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I13-13 (CANL) - I39-4 (CG)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I13-14 (CANH) - I39-16 (BAT)
    P - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I13-13 (CANL) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

C238830E01


Text in Illustration 
*a
Component without harness connected
(Brake Actuator Assembly (Skid Control ECU))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. C238832E28
  3. Disconnect the brake actuator assembly (skid control ECU) connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly (Skid Control ECU))

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A49-26 (CANH) - A49-14 (CANL)
    GR - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    A49-26 (CANH) - A49-38 (GND1)
    GR - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A49-14 (CANL) - A49-38 (GND1)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    A49-26 (CANH) - A49-25 (+BS)
    GR - L
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A49-14 (CANL) - A49-25 (+BS)
    W - L
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


STEERING SENSOR
C156493E67
Text in Illustration 
*a
Front view of wire harness connector
(to Steering Sensor)
  1. Disconnect the cable from the negative (-) battery terminal.

  2. Disconnect the steering sensor connector.

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I29-3 (CANH) - I29-2 (CANL)
    V - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I29-3 (CANH) - I29-1 (ESS)
    V - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I29-2 (CANL) - I29-1 (ESS)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I29-3 (CANH) - I29-5 (BAT)
    V - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I29-2 (CANL) - I29-5 (BAT)
    W - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


YAW RATE SENSOR (SEPARATE TYPE YAW RATE SENSOR)
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the connector of the yaw rate sensor.


    C250923E01


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I172-3 (CANH) - I172-2 (CANL)
    BE - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I172-3 (CANH) - I39-16 (BAT)
    BE - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I172-2 (CANL) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I172-3 (CANH) - I172-1 (GNDA)
    BE - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I172-2 (CANL) - I172-1 (GNDA)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher


POWER STEERING ECU ASSEMBLY (for 2AR-FE w/o Wireless Door Lock)

C240518E01


Text in Illustration 
*a
Component without harness connected
(Power Steering ECU Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the power steering ECU assembly connectors.


    C240488E06


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    j1-7 (CANH) - j1-8 (CANL)
    Y - SB
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    j1-7 (CANH) - j2-2 (PGND)
    Y - B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    j1-8 (CANL) - j2-2 (PGND)
    SB - B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    j1-7 (CANH) - j2-1 (PIG)
    Y - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    j1-8 (CANL) - j2-1 (PIG)
    SB - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


POWER STEERING ECU WITH MOTOR ASSEMBLY (for 2AR-FE w/ Wireless Door Lock)

C245077E03


Text in Illustration 
*a
Component without harness connected
(Power Steering ECU with Motor Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the power steering ECU with motor assembly connectors.


    C240488E06


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU with Motor Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    j1-7 (CANH) - j1-8 (CANL)
    Y - SB
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    j1-7 (CANH) - j2-2 (PGND)
    Y - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    j1-8 (CANL) - j2-2 (PGND)
    SB -W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    j1-7 (CANH) - j2-1 (PIG)
    Y - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    j1-8 (CANL) - j2-1 (PIG)
    SB - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


POWER STEERING ECU ASSEMBLY (for 2GR-FE w/ Wireless Door Lock)

C239855E05


Text in Illustration 
*a
Component without harness connected
(Power Steering ECU Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the power steering ECU assembly connectors.


    C240514E04


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    j3-4 (CANH) - j3-8 (CANL)
    Y - SB
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    j3-4 (CANH) - j2-2 (PGND)
    Y - B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    j3-8 (CANL) - j2-2 (PGND)
    SB - B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    j3-4 (CANH) - j2-1 (PIG)
    Y - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    j3-8 (CANL) - j2-1 (PIG)
    SB - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


AIRBAG SENSOR ASSEMBLY

C188802E22


Text in Illustration 
*1
DLC3
-
-
*a
Front view of wire harness connector
(to Airbag Sensor Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.

  2. Disconnect the airbag sensor assembly connector.

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I47-13 (CANH) - I47-22 (CANL)
    Y - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I47-13 (CANH) - I47-25 (E1)
    Y - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I47-22 (CANL) - I47-25 (E1)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I47-13 (CANH) - I39-16 (BAT)
    Y - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I47-22 (CANL) - I39-16 (BAT)
    W - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


SMART KEY ECU ASSEMBLY (CERTIFICATION ECU) (w/ Smart Key System)

B264892E31


Text in Illustration 
*a
Component without harness connected
(Smart Key ECU Assembly (Certification ECU))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the smart key ECU assembly connector.


    C240482E05


    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Smart Key ECU Assembly (Certification ECU))
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I78-14 (CANH) - I78-15 (CANL)
    L - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I78-14 (CANH) - A43-11 (E)
    L - W
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I78-15 (CANL) - A43-11 (E)
    W - W
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I78-14 (CANH) - A43-2 (+B)
    L - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I78-15 (CANL) - A43-2 (+B)
    W - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type w/o Intuitive Parking Assist System)

C250212E01


Text in Illustration 
*A
for 6 Speakers
*B
for 10 Speakers
*C
w/ Navigation System
-
-
*a
Component without harness connected
(Radio and Display Receiver Assembly (for Radio and Display Type w/o Intuitive Parking Assist System))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the radio and display receiver assembly connectors.


    C250213E01


    Text in Illustration 
    *A
    for 6 Speakers
    *B
    for 10 Speakers
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I155-9 (CANH) - I155-10 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I155-9 (CANH) - I152-7 (GND1)*1
    I155-9 (CANH) - I134-20 (GND1)*2
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I155-10 (CANL) - I152-7 (GND1)*1
    I155-10 (CANL) - I134-20 (GND1)*2
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I155-9 (CANH) - I152-4 (+B1)*1
    I155-9 (CANH) - I134-1 (+B1)*2
    R - L-Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I155-10 (CANL) - I152-4 (+B1)*1
    I155-10 (CANL) - I134-1 (+B1)*2
    W - L-Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    1. *1: for 6 speakers
    2. *2: for 10 speakers


NAVIGATION ECU SUB-ASSEMBLY (for Radio and Display Type w/ Intuitive Parking Assist System)

E225806E13


Text in Illustration 
*a
Component without harness connected
(Navigation ECU Sub-assembly (for Radio and Display Type w/ Intuitive Parking Assist System))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the navigation ECU sub-assembly connectors.


    C240506E15


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation ECU Sub-assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I67-9 (CANH) - I67-10 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I67-9 (CANH) - I64-7 (GND1)
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I67-10 (CANL) - I64-7 (GND1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I67-9 (CANH) - I64-4 (+B1)
    R - L-Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I67-10 (CANL) - I64-4 (+B1)
    W - L-Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


NAVIGATION ECU SUB-ASSEMBLY (for Navigation Receiver Type)

E225806E13


Text in Illustration 
*a
Component without harness connected
(Navigation ECU Sub-assembly (for Navigation Receiver Type))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the navigation ECU sub-assembly connectors.


    C240506E15


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation ECU Sub-assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I67-9 (CANH) - I67-10 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I67-9 (CANH) - I64-7 (GND1)
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I67-10 (CANL) - I64-7 (GND1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I67-9 (CANH) - I64-4 (+B1)
    R - L-Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I67-10 (CANL) - I64-4 (+B1)
    W - L-Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)

E226604E12


Text in Illustration 
*a
Component without harness connected
(Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the air conditioning amplifier assembly connector.


    C188799E36


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I77-11 (CANH) - I77-12 (CANL)
    V - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I77-11 (CANH) - I77-14 (GND)
    V - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I77-12 (CANL) - I77-14 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I77-11 (CANH) - I77-21 (B)
    V - Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I77-12 (CANL) - I77-21 (B)
    W - Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)

E226604E12


Text in Illustration 
*a
Component without harness connected
(Air Conditioning Amplifier Assembly (for Manual Air Conditioning System))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the air conditioning amplifier assembly connector.


    C188799E36


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I77-11 (CANH) - I77-12 (CANL)
    V - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I77-11 (CANH) - I77-14 (GND)
    V - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I77-12 (CANL) - I77-14 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I77-11 (CANH) - I77-21 (B)
    V - Y
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I77-12 (CANL) - I77-21 (B)
    W - Y
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


CLEARANCE WARNING ECU ASSEMBLY (w/ Intuitive Parking Assist System)

C240483E04


Text in Illustration 
*1
DLC3
-
-
*a
Front view of wire harness connector
(to Clearance Warning ECU Assembly)
-
-
  1. Disconnect the cable from the negative (-) battery terminal.

  2. Disconnect the clearance warning ECU assembly connector.

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I82-17 (R1) - I82-18 (R2)
    BE - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I82-17 (R1) - I82-30 (E)
    BE - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I82-18 (R2) - I82-30 (E)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I82-17 (R1) - I39-16 (BAT)
    BE - R
    CAN communication line H - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I82-18 (R2) - I39-16 (BAT)
    W - R
    CAN communication line L - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


NETWORK GATEWAY ECU (w/ Blind Spot Monitor System)

C238891E03


Text in Illustration 
*a
Component without harness connected
(Network Gateway ECU (w/ Blind Spot Monitor System))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. C238892E27
  3. Disconnect the network gateway ECU connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Network Gateway ECU)

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    V bus Branch Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I81-16 (CA1H) - I81-15 (CA1L)
    G - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    I81-16 (CA1H) - I81-4 (GND)
    G - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I81-15 (CA1L) - I81-4 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I81-16 (CA1H) - I81-2 (BATT)
    G - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I81-15 (CA1L) - I81-2 (BATT)
    W - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    Sub bus 2 Main Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I81-13 (CA2H) - I81-12 (CA2L)
    G - LG
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    I81-13 (CA2H) - I81-4 (GND)
    G - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I81-12 (CA2L) - I81-4 (GND)
    LG - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    I81-13 (CA2H) - I81-2 (BATT)
    G - W
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    I81-12 (CA2L) - I81-2 (BATT)
    LG - W
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)

E211805E11


Text in Illustration 
*a
Component without harness connected
(Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the blind spot monitor sensor LH connector.


    C240489E10


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Blind Spot Monitor Sensor LH)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T10-8 (CA1P) - T10-4 (CA1N)
    R - B
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    T10-8 (CA1P) - T10-1 (BLGD)
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    T10-4 (CA1N) - T10-1 (BLGD)
    B - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    T10-8 (CA1P) - I39-16 (BAT)
    R - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    T10-4 (CA1N) - I39-16 (BAT)
    B - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)

E211805E12


Text in Illustration 
*a
Component without harness connected
(Blind Spot Monitor Sensor RH (w/ Blind Spot Monitor System))
-
-
  1. Disconnect the cable from the negative (-) battery terminal.



  2. Disconnect the blind spot monitor sensor RH connector.


    C240489E11


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Blind Spot Monitor Sensor RH)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O28-8 (CA1P) - O28-4 (CA1N)
    R - B
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω
    O28-8 (CA1P) - O28-1 (BRGD)
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    O28-4 (CA1N) - O28-1 (BRGD)
    B - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    O28-8 (CA1P) - I39-16 (BAT)
    R - R
    HIGH-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    O28-4 (CA1N) - I39-16 (BAT)
    B - R
    LOW-level CAN bus line - Battery positive (+)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher