LIGHTING SYSTEM > Low Beam Headlight Circuit |
| for HID Headlight: |

| for Halogen Headlight: |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Check that the relay operates.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Headlight Relay | Headlight relay (Low beam headlights) | ON/OFF | - |
|
| ||||
| OK | ||
| ||
| 2.INSPECT H-LP RELAY |
Remove the H-LP relay from the engine room relay block.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Voltage applied between terminals 1 and 2 | Below 1 Ω |
| *a | Component without harness connected (H-LP relay) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (H-LP MAIN FUSE - H-LP RELAY) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Relay Terminal 2 - Body ground | Always | 11 to 14 V |
| Relay Terminal 5 - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH) |
Disconnect the A24*1 or A17*2 headlight assembly LH connector.
Disconnect the A66*1 or A60*2 headlight assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Relay Terminal 3 - A24-2 (LO) | Always | Below 1 Ω |
| Relay Terminal 3 - A66-2 (LO) | Always | Below 1 Ω |
| Relay Terminal 3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| Relay Terminal 3 - A17-2 (LO) | Always | Below 1 Ω |
| Relay Terminal 3 - A60-2 (LO) | Always | Below 1 Ω |
| Relay Terminal 3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Relay Terminal 1 - 3D-12 | Always | Below 1 Ω |
| Relay Terminal 1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
Remove the instrument panel junction block assembly (Click here).
![]() |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3D-12 - MB-15 (HRLY) | Always | Below 1 Ω |
| 3D-12 - Body ground | Always | 10 kΩ or higher |
| *a | Component without harness connected (Instrument Panel Junction Block Assembly) |
|
| ||||
| OK | ||
| ||