Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

DTC    B1244    Light Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The automatic light control sensor detects the ambient light. The sensor creates an electrical signal based on the amount of light, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.

DTC No.
DTC Detecting Condition
Trouble Area
B1244
  1. Malfunction in automatic light control sensor
  2. Open or short in automatic light control sensor circuit
  1. Automatic light control sensor
  2. Harness or connector
  3. Main body ECU (multiplex network body ECU)

WIRING DIAGRAM


E223761E03


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the display on the Techstream.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Illumination Rate info
    Illumination rate information/0.00 ms to 2162.65 ms
    Value is output according to ambient light levels
    -

    OK:
    Normal condition listed above is displayed.



NG
Go to step 2
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
  1. Disconnect the I61*1 or I132*2 automatic light control sensor connector.

  1. Disconnect the I13 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Automatic Air Conditioning System 
    Tester Connection
    Condition
    Specified Condition
    I13-22 (CLTE) - I61-3 (CLTE)
    Always
    Below 1 Ω
    I13-21 (CLTS) - I61-5 (CLTS)
    Always
    Below 1 Ω
    I13-20 (CLTB) - I61-6 (CLTB)
    Always
    Below 1 Ω
    I13-22 (CLTE) - Body ground
    Always
    10 kΩ or higher
    I13-21 (CLTS) - Body ground
    Always
    10 kΩ or higher
    I13-20 (CLTB) - Body ground
    Always
    10 kΩ or higher
    for Manual Air Conditioning System 
    Tester Connection
    Condition
    Specified Condition
    I13-22 (CLTE) - I132-5 (CLTE)
    Always
    Below 1 Ω
    I13-21 (CLTS) - I132-4 (CLTS)
    Always
    Below 1 Ω
    I13-20 (CLTB) - I132-3 (CLTB)
    Always
    Below 1 Ω
    I13-22 (CLTE) - Body ground
    Always
    10 kΩ or higher
    I13-21 (CLTS) - Body ground
    Always
    10 kΩ or higher
    I13-20 (CLTB) - Body ground
    Always
    10 kΩ or higher

  1. *1: for Automatic Air Conditioning System
  2. *2: for Manual Air Conditioning System


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


    E173035E02
  1. Reconnect the I13 main body ECU (multiplex network body ECU) connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I13-20 (CLTB) - I13-22 (CLTE)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I13-22 (CLTE) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Main Body ECU (Multiplex Network Body ECU))



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK


4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR


  1. for Automatic Air Conditioning System



      E161973E04
    1. Reconnect the I61 automatic light control sensor connector.

    2. Connect an oscilloscope to the automatic light control sensor connector.
      Text in Illustration 
      *a
      Component with harness connected
      (Automatic Light Control Sensor)



    3. B113714E01
    4. Check the waveform.

      OK:
      Tester Connection
      Tool Setting
      Condition
      Specified Condition
      I61-3 (CLTE) - I61-5 (CLTS)
      5 V/DIV., 5 ms./DIV.
      Ignition switch ON, light control switch in AUTO position
      Correct waveform is as shown

      HINT:
      If the ambient light becomes brighter, width A becomes narrower.



  1. for Manual Air Conditioning System



      E236974E01
    1. Reconnect the I132 automatic light control sensor connector.

    2. Connect an oscilloscope to the automatic light control sensor connector.
      Text in Illustration 
      *a
      Component with harness connected
      (Automatic Light Control Sensor)



    3. B113714E01
    4. Check the waveform.

      OK:
      Tester Connection
      Tool Setting
      Condition
      Specified Condition
      I132-5 (CLTE) - I132-4 (CLTS)
      5 V/DIV., 5 ms./DIV.
      Ignition switch ON, light control switch in AUTO position
      Correct waveform is as shown

      HINT:
      If the ambient light becomes brighter, width A becomes narrower.



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)