POWER WINDOW CONTROL SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / D-Door Motor or Main Body / Data List.
Read the Data List according to the display on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Door P/W Auto SW | Driver door power window auto switch signal / ON or OFF | ON: Driver door power window auto switch operated OFF: Driver door power window auto switch not operated | - |
| D Door P/W Up SW | Driver door power window manual up switch signal / ON or OFF | ON: Driver door power window manual up switch operated OFF: Driver door power window manual up switch not operated | - |
| D Door P/W Down SW | Driver door power window manual down switch signal / ON or OFF | ON: Driver door power window manual down switch operated OFF: Driver door power window manual down switch not operated | - |
| Glass Position (Close - 1/4) | Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution | OK: Normal manual up operation Caution: Jam detected in the specified range | Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Glass Position (1/4 - 2/4) | Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution | OK: Normal manual up operation Caution: Jam detected in the specified range | Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Glass Position (2/4 - 3/4) | Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution | OK: Normal manual up operation Caution: Jam detected in the specified range | Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Glass Position (3/4 - Open) | Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution | OK: Normal manual up operation Caution: Jam detected in the specified range | Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Number of Trouble Codes | Number of trouble codes / Min.: 0 or Max.: 255 | Number of DTCs will be displayed | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Door Key SW-Lock | Driver door lock/unlock switch lock signal (key-linked lock switch) / ON or OFF | ON: Driver door key cylinder turned to lock position OFF: Driver door key cylinder turned to except lock position | - |
| D Door Key SW-UL | Driver door lock/unlock switch unlock signal (key-linked unlock switch) / ON or OFF | ON: Driver door key cylinder turned to unlock position OFF: Driver door key cylinder turned to except unlock position | - |
| FR Door Courtesy | Front door courtesy light switch RH / ON or OFF | ON: Front door RH closed OFF: Front door RH open | - |
| FL Door Courtesy | Front door courtesy light switch LH / ON or OFF | ON: Front door LH closed OFF: Front door LH open | - |
| Door Key P/W Up | Door key linked power window up / ON or OFF | Customization status displayed | - |
| Door key P/W Down | Door key linked power window down / ON or OFF | Customization status displayed | - |
| P/W Down W/ Transmit* | Wireless transmitter linked power window down / ON or OFF | Customization status displayed | - |
| P/W Wireless Ope Buzz* | Buzzer sounds of wireless power window / ON or OFF | Customization status displayed | - |
| Communication D-Door Motor | Connection status between power window regulator motor assembly LH (for driver door) and main body ECU (multiplex network body ECU) / OK or STOP | OK: Normal communication STOP: Communication stopped | - |
| ACTIVE TEST |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / D-Door Motor or Main Body / Active Test.
Perform the Active Test according to the display on the Techstream.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Power Window | Power window | OFF / UP / DOWN | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
| IG OFF P/W Control Permission Output | Power window | OFF / ON | Perform this Active Test with the ignition switch off |