Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type)

NAVIGATION SYSTEM (for Radio and Display Type) > Speaker Circuit

for Preparation Click here


DESCRIPTION

for 6 Speakers:
  1. If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.
  3. If a short is detected in a speaker circuit, no sound can be heard from the speakers.
for 10 Speakers:
  1. If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, DCM (telematics transceiver)*1 or speakers.
  3. If a short is detected in a speaker circuit, no sound can be heard from the speakers.
  4. *1: w/ Manual (SOS) Switch

WIRING DIAGRAM


for 6 Speakers

E226481E10


for 10 Speakers

E226482E05


E226483E06


INSPECTION PROCEDURE

1.CONFIRM MODEL

Result:
Result
Proceed to
for 6 Speakers
A
for 10 Speakers
B



B
Go to step 7
A


2.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the radio and display receiver assembly and speakers.

  1. Measure the resistance between each of the front No. 2 speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I152-1 (FR+) - I83-4 (TWR+)
    Always
    Below 1 Ω
    I152-5 (FR-) - I83-2 (TWR-)
    Always
    Below 1 Ω
    I152-2 (FL+) - I1-4 (TWL+)
    Always
    Below 1 Ω
    I152-6 (FL-) - I1-2 (TWL-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I83-3 (+) - J5-1
    Always
    Below 1 Ω
    I83-1 (-) - J5-2
    Always
    Below 1 Ω
    I1-3 (+) - K5-1
    Always
    Below 1 Ω
    I1-1 (-) - K5-2
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I153-1 (RR+) - O18-1
    Always
    Below 1 Ω
    I153-3 (RR-) - O18-2
    Always
    Below 1 Ω
    I153-2 (RL+) - O21-1
    Always
    Below 1 Ω
    I153-6 (RL-) - O21-2
    Always
    Below 1 Ω

  1. Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I152-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    I152-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    I152-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    I152-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    I153-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    I153-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    I153-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    I153-6 (RL-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I83-3 (+) - Body ground
    Always
    10 kΩ or higher
    I83-1 (-) - Body ground
    Always
    10 kΩ or higher
    I1-3 (+) - Body ground
    Always
    10 kΩ or higher
    I1-1 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


  1. Resistance check



      E219303E36
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J5-1 - J5-2
      Always
      3.2 to 4.8 Ω
      K5-1 - K5-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


  1. Resistance check



      E226097E13
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I83-2 (TWR-) - I83-4 (TWR+)
      Always
      10 kΩ or higher
      I83-1 (-) - I83-2 (TWR-)
      Always
      Below 1 Ω
      I83-3 (+) - I83-4 (TWR+)
      Always
      Below 1 Ω
      I1-2 (TWL-) - I1-4 (TWL+)
      Always
      10 kΩ or higher
      I1-1 (-) - I1-2 (TWL-)
      Always
      Below 1 Ω
      I1-3 (+) - I1-4 (TWL+)
      Always
      Below 1 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


5.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
  1. Check that the malfunction disappears when a known good speaker is installed (Click here).

    OK:
    Malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.



NG
Go to step 6
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE) 

6.INSPECT REAR SPEAKER ASSEMBLY


  1. Resistance check



      E219303E37
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O18-1 - O18-2
      Always
      3.2 to 4.8 Ω
      O21-1 - O21-2
      Always
      3.2 to 4.8 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear Speaker Assembly)



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the stereo component amplifier assembly, DCM (telematics transceiver)*1 and speakers.

    1. *1: w/ Manual (SOS) Switch

  1. w/ Manual (SOS) Switch
    Measure the resistance between the stereo component amplifier assembly and the DCM (telematics transceiver) to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) - I135-2 (SPI+)
    Always
    Below 1 Ω
    I68-30 (FR-) - I135-3 (SPI-)
    Always
    Below 1 Ω

  1. w/ Manual (SOS) Switch
    Measure the resistance between the front No. 1 speaker assembly RH and the DCM (telematics transceiver) to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J5-1 (+) - I135-5 (SPO+)
    Always
    Below 1 Ω
    J5-2 (-) - I135-6 (SPO-)
    Always
    Below 1 Ω

  1. w/o Manual (SOS) Switch
    Measure the resistance between the front No. 1 speaker assembly RH and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) - J5-1 (+)
    Always
    Below 1 Ω
    I68-30 (FR-) - J5-2 (-)
    Always
    Below 1 Ω

  1. Measure the resistance between the front No. 1 speaker assembly LH and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-11 (FL+) - K5-1 (+)
    Always
    Below 1 Ω
    I68-26 (FL-) - K5-2 (-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-12 (TWR+) - I84-4
    Always
    Below 1 Ω
    I68-27 (TWR-) - I84-3
    Always
    Below 1 Ω
    I68-14 (TWL+) - I2-4
    Always
    Below 1 Ω
    I68-29 (TWL-) - I2-3
    Always
    Below 1 Ω

  1. Measure the resistance between the front No. 3 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-13 (CTR+) - I60-2
    Always
    Below 1 Ω
    I68-28 (CTR-) - I60-1
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-10 (SR+) - O19-2
    Always
    Below 1 Ω
    I68-25 (SR-) - O19-1
    Always
    Below 1 Ω
    I68-9 (SL+) - O20-2
    Always
    Below 1 Ω
    I68-24 (SL-) - O20-1
    Always
    Below 1 Ω

  1. Measure the resistance between the rear speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-8 (WF1+) - O22-1
    Always
    Below 1 Ω
    I68-23 (WF1-) - O22-2
    Always
    Below 1 Ω

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) - Body ground
    Always
    10 kΩ or higher
    I68-30 (FR-) - Body ground
    Always
    10 kΩ or higher
    I68-11 (FL+) - Body ground
    Always
    10 kΩ or higher
    I68-26 (FL-) - Body ground
    Always
    10 kΩ or higher
    I68-12 (TWR+) - Body ground
    Always
    10 kΩ or higher
    I68-27 (TWR-) - Body ground
    Always
    10 kΩ or higher
    I68-14 (TWL+) - Body ground
    Always
    10 kΩ or higher
    I68-29 (TWL-) - Body ground
    Always
    10 kΩ or higher
    I68-13 (CTR+) - Body ground
    Always
    10 kΩ or higher
    I68-28 (CTR-) - Body ground
    Always
    10 kΩ or higher
    I68-10 (SR+) - Body ground
    Always
    10 kΩ or higher
    I68-25 (SR-) - Body ground
    Always
    10 kΩ or higher
    I68-9 (SL+) - Body ground
    Always
    10 kΩ or higher
    I68-24 (SL-) - Body ground
    Always
    10 kΩ or higher
    I68-8 (WF1+) - Body ground
    Always
    10 kΩ or higher
    I68-23 (WF1-) - Body ground
    Always
    10 kΩ or higher

  1. w/ Manual (SOS) Switch
    Measure the resistance between the DCM (telematics transceiver) and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I135-5 (SPO+) - Body ground
    Always
    10 kΩ or higher
    I135-6 (SPO-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E219303E38
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J5-1 (+) - J5-2 (-)
      Always
      4.6 to 6.6 Ω
      K5-1 (+) - K5-2 (-)
      Always
      4.6 to 6.6 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


9.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E219304E20
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I84-4 - I84-3
      Always
      3.4 to 5.2 Ω
      I2-4 - I2-3
      Always
      3.4 to 5.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


10.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    E222247E16
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I60-2 - I60-1
      Always
      6.8 to 10.2 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front No. 3 Speaker Assembly)



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


11.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E222247E17
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O19-2 - O19-1
      Always
      6.8 to 10.2 Ω
      O20-2 - O20-1
      Always
      6.8 to 10.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear No. 2 Speaker Assembly)



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK


12.INSPECT REAR SPEAKER ASSEMBLY


    E219303E39
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O22-1 - O22-2
      Always
      4.8 to 6.8 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Rear Speaker Assembly)

  1. Proceed to the next step based on the inspection result.

    Result:
    Condition
    Proceed to
    OK (w/ Manual (SOS) Switch)
    A
    OK (w/o Manual (SOS) Switch)
    B
    NG
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE REAR SPEAKER ASSEMBLY (Click here)
A


13.INSPECT DCM (TELEMATICS TRANSCEIVER)


    E169849E18
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I135-2 (SPI+) - I135-5 (SPO+)
      Always
      Below 1 Ω
      I135-3 (SPI-) - I135-6 (SPO-)
      Always
      Below 1 Ω
      I135-2 (SPI+) - I135-3 (SPI-)
      Always
      10 kΩ or higher
      I135-5 (SPO+) - I135-6 (SPO-)
      Always
      10 kΩ or higher
      I135-2 (SPI+) - Body ground
      Always
      10 kΩ or higher
      I135-3 (SPI-) - Body ground
      Always
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (DCM (Telematics Transceiver))



NG
REPLACE DCM (TELEMATICS TRANSCEIVER) (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)