Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

NAVIGATION SYSTEM (for Navigation Receiver Type) > Speaker Circuit

for Preparation Click here


DESCRIPTION

  1. If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
  2. Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, DCM (telematics transceiver)*1 or speakers.
  3. If a short is detected in a speaker circuit, no sound can be heard from the speakers.
  1. *1: w/ Manual (SOS) Switch

WIRING DIAGRAM


E226482E02


E226483E02


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the stereo component amplifier assembly, DCM (telematics transceiver)*1 and speakers.

    1. *1: w/ Manual (SOS) Switch

  1. w/ Manual (SOS) Switch
    Measure the resistance between the stereo component amplifier assembly and the DCM (telematics transceiver) to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) - I135-2 (SPI+)
    Always
    Below 1 Ω
    I68-30 (FR-) - I135-3 (SPI-)
    Always
    Below 1 Ω

  1. w/ Manual (SOS) Switch
    Measure the resistance between the front No. 1 speaker assembly RH and the DCM (telematics transceiver) to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J5-1 (+) - I135-5 (SPO+)
    Always
    Below 1 Ω
    J5-2 (-) - I135-6 (SPO-)
    Always
    Below 1 Ω

  1. w/o Manual (SOS) Switch
    Measure the resistance between the front No. 1 speaker assembly RH and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) - J5-1 (+)
    Always
    Below 1 Ω
    I68-30 (FR-) - J5-2 (-)
    Always
    Below 1 Ω

  1. Measure the resistance between the front No. 1 speaker assembly LH and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-11 (FL+) - K5-1 (+)
    Always
    Below 1 Ω
    I68-26 (FL-) - K5-2 (-)
    Always
    Below 1 Ω

  1. Measure the resistance between each of the front No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-12 (TWR+) - I84-4
    Always
    Below 1 Ω
    I68-27 (TWR-) - I84-3
    Always
    Below 1 Ω
    I68-14 (TWL+) - I2-4
    Always
    Below 1 Ω
    I68-29 (TWL-) - I2-3
    Always
    Below 1 Ω

  1. Measure the resistance between the front No. 3 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-13 (CTR+) - I60-2
    Always
    Below 1 Ω
    I68-28 (CTR-) - I60-1
    Always
    Below 1 Ω

  1. Measure the resistance between each of the rear No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-10 (SR+) - O19-2
    Always
    Below 1 Ω
    I68-25 (SR-) - O19-1
    Always
    Below 1 Ω
    I68-9 (SL+) - O20-2
    Always
    Below 1 Ω
    I68-24 (SL-) - O20-1
    Always
    Below 1 Ω

  1. Measure the resistance between the rear speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-8 (WF1+) - O22-1
    Always
    Below 1 Ω
    I68-23 (WF1-) - O22-2
    Always
    Below 1 Ω

  1. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) - Body ground
    Always
    10 kΩ or higher
    I68-30 (FR-) - Body ground
    Always
    10 kΩ or higher
    I68-11 (FL+) - Body ground
    Always
    10 kΩ or higher
    I68-26 (FL-) - Body ground
    Always
    10 kΩ or higher
    I68-12 (TWR+) - Body ground
    Always
    10 kΩ or higher
    I68-27 (TWR-) - Body ground
    Always
    10 kΩ or higher
    I68-14 (TWL+) - Body ground
    Always
    10 kΩ or higher
    I68-29 (TWL-) - Body ground
    Always
    10 kΩ or higher
    I68-13 (CTR+) - Body ground
    Always
    10 kΩ or higher
    I68-28 (CTR-) - Body ground
    Always
    10 kΩ or higher
    I68-10 (SR+) - Body ground
    Always
    10 kΩ or higher
    I68-25 (SR-) - Body ground
    Always
    10 kΩ or higher
    I68-9 (SL+) - Body ground
    Always
    10 kΩ or higher
    I68-24 (SL-) - Body ground
    Always
    10 kΩ or higher
    I68-8 (WF1+) - Body ground
    Always
    10 kΩ or higher
    I68-23 (WF1-) - Body ground
    Always
    10 kΩ or higher

  1. w/ Manual (SOS) Switch
    Measure the resistance between the DCM (telematics transceiver) and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I135-5 (SPO+) - Body ground
    Always
    10 kΩ or higher
    I135-6 (SPO-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E219303E40
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J5-1 (+) - J5-2 (-)
      Always
      4.6 to 6.6 Ω
      K5-1 (+) - K5-2 (-)
      Always
      4.6 to 6.6 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 1 Speaker Assembly)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E219304E15
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I84-4 - I84-3
      Always
      3.4 to 5.2 Ω
      I2-4 - I2-3
      Always
      3.4 to 5.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Front No. 2 Speaker Assembly)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    E222247E10
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I60-1 - I60-2
      Always
      6.8 to 10.2 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front No. 3 Speaker Assembly)



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


5.INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    E222247E11
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O19-1 - O19-2
      Always
      6.8 to 10.2 Ω
      O20-1 - O20-2
      Always
      6.8 to 10.2 Ω

      Text in Illustration 
      *A
      for RH
      *B
      for LH
      *a
      Component without harness connected
      (Rear No. 2 Speaker Assembly)



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK


6.INSPECT REAR SPEAKER ASSEMBLY


    E219303E16
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O22-1 - O22-2
      Always
      4.8 to 6.8 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Rear Speaker Assembly)

  1. Proceed to the next step based on the inspection result.

    Result:
    Condition
    Proceed to
    OK (w/ Manual (SOS) Switch)
    A
    OK (w/o Manual (SOS) Switch)
    B
    NG
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE REAR SPEAKER ASSEMBLY (Click here)
A


7.INSPECT DCM (TELEMATICS TRANSCEIVER)


    E169849E15
  1. Resistance check

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I135-2 (SPI+) - I135-5 (SPO+)
      Always
      Below 1 Ω
      I135-3 (SPI-) - I135-6 (SPO-)
      Always
      Below 1 Ω
      I135-2 (SPI+) - I135-3 (SPI-)
      Always
      10 kΩ or higher
      I135-5 (SPO+) - I135-6 (SPO-)
      Always
      10 kΩ or higher
      I135-2 (SPI+) - Body ground
      Always
      10 kΩ or higher
      I135-3 (SPI-) - Body ground
      Always
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (DCM (Telematics Transceiver))



NG
REPLACE DCM (TELEMATICS TRANSCEIVER) (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)