Home › Drivetrain ยท U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > TERMINALS OF ECU

for Preparation Click here



TCM

C133222E14

HINT:
Each TCM terminal standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the TCM terminals.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E7-15 (R) - E7-8 (E1)
L - BR
R shift position switch signal
Engine switch on (IG) and shift lever in R
11 to 14 V
Engine switch on (IG) and shift lever in any position except R
Below 1 V
E7-16 (D) - E7-8 (E1)
R - BR
D shift position switch signal
Engine switch on (IG) and shift lever in D and S
11 to 14 V
Engine switch on (IG) and shift lever in any position except D and S
Below 1 V
E7-12 (STP) - E7-8 (E1)
GR - BR
Stop light switch signal
Brake pedal is depressed
7.5 to 14 V
Brake pedal is released
Below 1.5 V
E7-11 (NSW) - E7-8 (E1)
R - BR
Park/neutral switch signal
Engine switch on (IG) and shift lever in P or N
Below 2 V
Engine switch on (IG) and shift lever in any position except P or N
11 to 14 V
E7-10 (STA) - E7-8 (E1)
Y - BR
Starter signal
Cranking (shift lever in P or N, engine switch START)
11 to 14 V
Engine switch on (IG) and shift lever in any position except P or N
Below 2 V
E7-3 (SPD) - E7-8 (E1)
G - BR
Speed signal from combination meter
Vehicle driving
Pulse generation
E7-1 (BATT) - E7-8 (E1)
W - BR
Battery (for measuring battery voltage and for TCM memory)
Always
9 to 14 V
E7-13 (IGSW) - E7-8 (E1)
B - BR
IG signal
Engine switch on (IG)
9 to 14 V
E7-18 (+B) - E7-8 (E1)
W - BR
Power source of TCM
Engine switch on (IG)
9 to 14 V
E7-6 (CAN+) - E7-8 (E1)
B - BR
CAN communication line
Engine switch on (IG)
Pulse generation
E7-7 (CAN-) - E7-8 (E1)
Y - BR
CAN communication line
Engine switch on (IG)
Pulse generation

ECM

HINT:
Each ECM terminal standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration below as a reference for the ECM terminals.

C239275E02


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A25-37 (S) - E26-49 (E1)
G - BR
S shift position switch signal
Engine switch on (IG) and shift lever in S
11 to 14 V
Engine switch on (IG) and shift lever in any position except S
Below 1 V
A25-34 (SFTU) - E26-49 (E1)
R - BR
Up shift switch signal
Engine switch on (IG) and shift lever in S
11 to 14 V
Engine switch on (IG) and shift lever in "+" (Up shift)
Below 1 V
A25-50 (SFTD) - E26-49 (E1)
V - BR
Down shift switch signal
Engine switch on (IG) and shift lever in S
11 to 14 V
Engine switch on (IG) and shift lever in "-" (Down shift)
Below 1 V