Home › Audio/Visual/Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM

REAR VIEW MONITOR SYSTEM > TERMINALS OF ECU

for Preparation Click here



REAR TELEVISION CAMERA ASSEMBLY


  1. Disconnect the T6 connector from the rear television camera assembly.


    E220918E01

  2. Measure the voltage of each terminal of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T6-6 (CB+) - Body ground
    B - Body ground
    Power source
    Ignition switch ON
    Shift lever in R*1
    5.5 to 7.05 V
    Within 60 seconds of turning the ignition switch to ACC*2
    5.5 to 7.05 V

    1. *1: for Navigation Receiver Type
    2. *2: for Radio and Display Type
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T6 connector to the rear television camera assembly.

  4. Check for pulses between each terminal of the connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T6-3 (CV+) - T6-2 (CV-)
    W - R
    Video signal
    Ignition switch ON
    Shift lever in R
    Camera lens not covered, displaying an image
    Pulse generation
    (See waveform 1)
    Ignition switch ON
    Shift lever in R
    Camera lens covered, blacking out screen
    Pulse generation
    (See waveform 2)

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.

    If the result is not as specified, the camera may have a malfunction.
    *1: for Navigation Receiver Type
    *2: for Radio and Display Type



  5. E171712E22
  6. Reference (Oscilloscope waveform):

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation ECU sub-assembly*1 or radio and display receiver assembly*2 with the connector connected.
    *1: for Navigation Receiver Type
    *2: for Radio and Display Type


    1. Waveform 1 (camera lens is not covered, displaying an image)
      Item
      Content
      Terminal No. (Symbol)
      T6-3 (CV+) - T6-2 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2 (camera lens is covered, blacking out the screen)
      Item
      Content
      Terminal No. (Symbol)
      T6-3 (CV+) - T6-2 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *a
      Waveform 1 (camera lens not covered, displaying an image)
      *b
      Waveform 2 (camera lens covered, blacking out the screen)
      *c
      Synchronization Signal
      *d
      Video Waveform


RADIO AND DISPLAY RECEIVER ASSEMBLY (NAVIGATION SYSTEM (for Radio and Display Type)) (Click here)

NAVIGATION ECU SUB-ASSEMBLY (NAVIGATION SYSTEM (for Navigation Receiver Type)) (Click here)

RADIO AND DISPLAY RECEIVER ASSEMBLY (AUDIO AND VISUAL SYSTEM (for Radio and Display Type without Intuitive Parking Assist System)) (Click here)