Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK COMBINATION METER ASSEMBLY


  1. Disconnect the I18 combination meter assembly connector.


    E224288E06

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I18-7 (ES) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the I18 combination meter assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I18-1 (B) - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    I18-13 (IG+) - Body ground
    L - Body ground
    Ignition power supply
    (IG signal)
    Ignition switch off
    Below 1 V
    I18-13 (IG+) - Body ground
    L - Body ground
    Ignition power supply
    (IG signal)
    Ignition switch ON
    11 to 14 V
    If the result is not as specified, the combination meter assembly may have a malfunction.


CHECK AIRBAG SENSOR ASSEMBLY (for Built-in Type Yaw Rate Sensor)

C109532E49


Terminal No.
Terminal Symbol
Destination
N5-10
LBE+
Front seat inner belt assembly LH
N5-18
LBE-
Front seat inner belt assembly LH
O7-16
FSR+
Occupant detection ECU
O7-24
FSR-
Occupant detection ECU

CHECK AIRBAG SENSOR ASSEMBLY (for Separate Type Yaw Rate Sensor)

C123353E54


Terminal No.
Terminal Symbol
Destination
N40-11
LBE+
Front seat inner belt assembly LH
N40-12
LBE-
Front seat inner belt assembly LH
O42-12
FSR+
Occupant detection ECU
O42-13
FSR-
Occupant detection ECU

CHECK OCCUPANT DETECTION ECU


  1. Measure the voltage according to the value(s) in the table below.


    C238368E04


    Text in Illustration 
    *A
    for TMMK Made
    *B
    for SIA Made

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specification
    d11-1 (+B) - d11-3 (GND)
    W - W-B
    Battery
    Always
    11 to 14 V
    d11-2 (DIA) - d11-3 (GND)
    GR - W-B
    Diagnosis (DLC3)
    Ignition switch ON, Techstream not connected to DLC3
    Below 1 V
    d11-3 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 V
    d11-4 (FSR-) - d11-3 (GND)
    Y - W-B*1
    LG - W-B*2
    Airbag sensor assembly communication line
    Always
    Below 1 V
    d11-5 (BGND) - d11-3 (GND)
    P - W-B
    Front passenger buckle switch ground line
    Always
    Below 1 V
    d11-6 (IG) - d11-3 (GND)
    B - W-B
    Power source
    Ignition switch ON
    11 to 14 V
    d11-7 (FSR+) - d11-4 (FSR-)
    L - Y*1
    L - YG*2
    Airbag sensor assembly communication line
    Ignition switch ON
    Pulse generation
    d11-8 (BSW) - d11-5 (BGND)
    G - P
    Front passenger buckle switch line
    Always
    Pulse generation
    d8-1 (SVC3) - d8-5 (SGD3)*1
    d18-1 (SVC3) - d18-5 (SGD3)*2
    GR - W-B
    Occupant classification sensor LH power supply line
    Ignition switch ON
    4.9 to 5.1 V
    d8-2 (SVC4) - d8-6 (SGD4)*1
    d18-2 (SVC4) - d18-6 (SGD4)*2
    V - W-B
    Occupant classification sensor RH power supply line
    Ignition switch ON
    4.9 to 5.1 V
    d8-3 (SIG3) - d8-5 (SGD3)*1
    d18-3 (SIG3) - d18-5 (SGD3)*2
    Y - W*1
    SB - W*2
    Occupant classification sensor LH signal line
    Ignition switch ON
    Pulse generation
    d8-4 (SIG4) - d8-6 (SGD4)*1
    d18-4 (SIG4) - d18-6 (SGD4)*2
    B - BR
    Occupant classification sensor RH signal line
    Ignition switch ON
    Pulse generation
    1. *1: for TMMK Made
    2. *2: for SIA Made
    If the result is not as specified, the occupant detection ECU may have a malfunction.