AUTOMATIC TRANSAXLE ASSEMBLY > INSTALLATION |
| 1. INSPECT TORQUE CONVERTER ASSEMBLY |
Inspect the one-way clutch.
![]() |
Press on the splines of the stator with a finger and rotate the stator. Check that the stator rotates smoothly when turned clockwise and rotates with difficulty when turned counterclockwise.
If necessary, clean the torque converter and recheck the one-way clutch.
Replace the torque converter if the one-way clutch still fails the inspection.
![]() | Difficult |
![]() | Smooth |
![]() |
Inspect the torque converter assembly.
If any of the following problems are present, replace the torque converter assembly.
| *a | Sample showing maximum allowable amount of powder in ATF |
Replace the ATF in the torque converter.
![]() |
Clean and check the oil cooler and oil pipe line.
![]() |
Prevent deformation of the torque converter and damage to the oil pump gear.
| *a | Correct |
| *b | Incorrect |
| *c | Bottom is damaged |
| 2. INSTALL TORQUE CONVERTER ASSEMBLY |
![]() |
Engage the splines of the input shaft and turbine runner.
![]() |
Engage the splines of the stator shaft and the stator while turning the torque converter assembly.
![]() |
Turn the torque converter assembly to insert the key of the oil pump drive gear into the groove of the torque converter assembly.
Clean the torque converter set bolt holes.
![]() |
Using a vernier caliper and straightedge, measure dimension A between the transaxle contact surface of the engine and the torque converter contact surface of the drive plate.
| *a | Engine Surface |
| *b | Drive Plate Surface |
![]() |
Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the previous step.
| 3. INSTALL TRANSMISSION CASE PLUG ASSEMBLY |
Apply ATF to a new O-ring and install it to the transmission case plug assembly.
Install the transmission case plug assembly to the automatic transaxle assembly.
| 4. INSTALL WIRE HARNESS CLAMP BRACKET |
Install the 4 wire harness clamp brackets to the automatic transaxle assembly with the 4 bolts.
| 5. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET |
Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.
| 6. INSTALL FRONT ENGINE MOUNTING BRACKET |
Install the front engine mounting bracket to the automatic transaxle assembly with the 3 bolts.
| 7. INSTALL TRANSMISSION OIL COOLER |
Install the transmission oil cooler to the front engine mounting bracket with the 3 bolts.
Install the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose.
| 8. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY |
![]() |
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter centerpiece.
| *1 | Torque Converter Centerpiece |
| *2 | Crankshaft |
![]() |
While keeping the engine and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the 9 bolts shown in the illustration.
| Bolt | Bolt Length | Torque |
| A | 55 mm (2.17 in.) | 64 N*m (653 kgf*cm, 47 ft.*lbf) |
| B | 50 mm (1.97 in.) | 46 N*m (469 kgf*cm, 34 ft.*lbf) |
| C | 32 mm (1.26 in.) | 44 N*m (449 kgf*cm, 32 ft.*lbf) |
| 33 mm (1.30 in.) | 43 N*m (438 kgf*cm, 32 ft.*lbf) |
| 9. INSTALL WIRE HARNESS |
Connect the 7 wire harness clamps and park/neutral position switch connector.
Install the ground cable with the bolt.
| 10. INSTALL WIRING HARNESS CONNECTOR |
Install the wiring harness connector to the automatic transaxle assembly.
![]() |
Install and tighten the 2 bolts in the order shown in the illustration.
![]() |
Connect the connector to the wiring harness connector.
Turn the lock lever and secure the connector with the lock lever.
| 11. INSTALL FRONT FRAME ASSEMBLY |
Install the engine mounting insulator LH with the nut.
Install the engine mounting insulator RH with the nut.
Install the front engine mounting insulator with the bolt.
Fully tighten the 9 temporarily installed nuts of the engine mounting insulators to the specified torque.

| *1 | Front Engine Mounting Insulator | *2 | Engine Mounting Insulator RH |
| *3 | Engine Mounting Insulator LH | - | - |
Install the 4 hole plugs.

| *1 | Engine Mounting Insulator RH | *2 | Engine Mounting Insulator LH |
| 12. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH |
Install a new front drive shaft hole snap ring LH.
| 13. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
Coat the spline of the front drive inboard joint assembly with ATF.
Coat the lip of the transaxle case oil seal with MP grease.
![]() |
Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.
![]() |
Apply mineral oil base grease to the areas indicated by the arrows in the illustration on the front drive shaft assembly LH contact surface of the front axle hub bearing.
![]() | Mineral Oil Base Grease |
![]() |
Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.
| *a | Matchmark |
| 14. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH |
Coat the spline of the front drive inboard joint assembly with ATF.
Coat the lip of the front transaxle case oil seal with MP grease.
Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.
Install the front drive shaft assembly RH.
![]() |
Install the bearing bracket hole snap ring and a new bolt.
![]() |
Apply mineral oil base grease to the areas indicated by the arrows in the illustration on the front drive shaft assembly RH contact surface of the front axle hub bearing.
![]() | Mineral Oil Base Grease |
![]() |
Align the matchmarks and install the front drive shaft assembly RH to the front axle hub sub-assembly.
| *a | Matchmark |
| 15. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE |
| 16. CHECK AUTOMATIC TRANSAXLE SYSTEM |