Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › INTEGRATION RELAY

INTEGRATION RELAY > INSPECTION

for Preparation Click here



1. INSPECT NO. 1 INTEGRATION RELAY



A256110E01


Text in Illustration 
*1
No. 1 Integration Relay
-
-


  1. EFI MAIN RELAY:



      A255141E01
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      No. 1 integration relay 1B-1 - No. 1 integration relay 1A-8
      Battery voltage is not applied between terminals 1C-7 and 1E-2
      10 kΩ or higher
      No. 1 integration relay 1B-1 - No. 1 integration relay 1A-8
      Battery voltage is applied between terminals 1C-7 and 1E-2
      Below 1 Ω
      No. 1 integration relay 1B-1 - No. 1 integration relay 1C-3
      No. 1 integration relay 1B-1 - No. 1 integration relay 1C-4
      No. 1 integration relay 1B-1 - No. 1 integration relay 1C-6
      No. 1 integration relay 1B-1 - No. 1 integration relay 1C-9
      No. 1 integration relay 1B-1 - No. 1 integration relay 1C-10

      Text in Illustration 
      *1
      No. 1 Integration Relay
      If the resistance is not as specified, replace the No. 1 integration relay.



  1. A/F HTR RELAY:



      A255141E01
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      No. 1 integration relay 1A-6 - No. 1 integration relay 1D-1
      Battery voltage is not applied between terminals 1A-8 and 1E-2
      10 kΩ or higher
      No. 1 integration relay 1A-6 - No. 1 integration relay 1D-1
      Battery voltage is applied between terminals 1A-8 and 1E-2
      Below 1 Ω
      No. 1 integration relay 1A-7 - No. 1 integration relay 1D-1

      Text in Illustration 
      *1
      No. 1 Integration Relay
      If the resistance is not as specified, replace the No. 1 integration relay.



  1. IG2 RELAY:



      A255141E01
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      No. 1 integration relay 1A-1 - No. 1 integration relay 1D-3
      Battery voltage is not applied between terminals 1C-8 and 1E-2
      10 kΩ or higher
      No. 1 integration relay 1A-1 - No. 1 integration relay 1D-3
      Battery voltage is applied between terminals 1C-8 and 1E-2
      Below 1 Ω
      No. 1 integration relay 1A-3 - No. 1 integration relay 1D-3
      No. 1 integration relay 1A-5 - No. 1 integration relay 1D-3
      No. 1 integration relay 1C-1 - No. 1 integration relay 1D-3
      No. 1 integration relay 1C-2 - No. 1 integration relay 1D-3
      No. 1 integration relay 1C-5 - No. 1 integration relay 1D-3

      Text in Illustration 
      *1
      No. 1 Integration Relay
      If the resistance is not as specified, replace the No. 1 integration relay.