Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY


    E227210
  1. Check that the slots, links and gears of the No. 1 air conditioning radiator damper servo sub-assembly are positioned in the correct orientation as shown in the illustration.

  1. Face the contact surfaces of the No. 1 air conditioning radiator damper servo sub-assembly and air conditioning radiator assembly for the No. 1 air conditioning radiator damper servo sub-assembly upward.



  1. Rotate the link of the air conditioning radiator assembly all the way to the left as shown in the illustration.


    E219270



  1. Rotate the link of the air conditioning radiator assembly to the bottom as shown in the illustration and confirm that the mode switching duct hole is fully closed.


    E219271E02


    Text in Illustration 
    *a
    Mode Switching Duct Hole
    -
    -



  1. Rotate the lever of the air conditioning radiator assembly to the top as shown in the illustration.


    E220372



  1. Rotate the link of the air conditioning radiator assembly to the in-line position as shown in the illustration.


    E220373E02


    Text in Illustration 
    *a
    In-line Position
    -
    -



    E219274E02
  1. Wrap the upper and lower links with vinyl tape to hold them in the in-line position.
    Text in Illustration 
    *1
    Vinyl Tape



  1. Install the link of the No. 1 air conditioning radiator damper servo sub-assembly to the link guide pin (A) of the air conditioning radiator assembly as shown in the illustration.


    E220374E02


    Text in Illustration 
    *1
    Guide
    *2
    No. 1 Air Conditioning Radiator Damper Servo Sub-assembly
    *a
    No. 1 Air Conditioning Radiator Damper Servo Sub-assembly Slot
    *b
    Link Guide Pin (A)
    *c
    Link Guide Pin (B)
    -
    -

  1. Install the guide hole of the No. 1 air conditioning radiator damper servo sub-assembly to the guide pin of the air conditioning radiator assembly as shown in the illustration.

  1. Temporarily install the screw (up to 4 or 5 threads).

    NOTICE:
    1. Make sure that the link guide pin (B) is inserted in the No. 1 air conditioning radiator damper servo sub-assembly slot.
    2. Avoid tilting the air conditioning radiator assembly during installation. This helps to prevent the guide pins from coming out of position.



    E219276
  1. Lift the No. 1 air conditioning radiator damper servo sub-assembly slightly to create clearance.



  1. Move the air conditioning radiator assembly gear so that alignment holes of the No. 1 air conditioning radiator damper servo sub-assembly and air conditioning radiator assembly are aligned.


    E219277E02


    Text in Illustration 
    *a
    No. 1 Air Conditioning Radiator Damper Servo Sub-assembly Alignment Hole
    *b
    Air Conditioning Radiator Assembly Alignment Hole
    *c
    Air Conditioning Radiator Assembly Alignment Gear Alignment Hole
    -
    -



    E219278
  1. Insert a screwdriver into the aligned holes as shown in the illustration.



  1. Make sure that all the links and gears are in the positions shown in the illustration.


    E220477E02


    Text in Illustration 
    *a
    Screwdriver is inserted into alignment holes.
    *b
    Link guide pin is inserted.
    *c
    Link is positioned to left side.
    *d
    Link is positioned at bottom.
    *e
    Each link guide pin is inserted in its air outlet control servo motor slot.
    *f
    Lever is positioned at top.
    *g
    Links are in-line.
    -
    -



    E219280
  1. Push the loose fitting No. 1 air conditioning radiator damper servo sub-assembly into position.

    NOTICE:
    1. Make sure that the No. 1 air conditioning radiator damper servo sub-assembly are fully pushed into position.
    2. After pushing the servos into position, keep them in place by holding them until the screws are installed.

    HINT:
    Push the No. 1 air conditioning radiator damper servo sub-assembly until a click sound is heard.

  1. Remove the screwdriver.



    E220478
  1. Fully install the top screw, and then install the No. 1 air conditioning radiator damper servo sub-assembly with the 2 remaining screws.

  1. Remove the vinyl tape.



2. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY


    E227203
  1. Install the heater radiator unit sub-assembly to the air conditioner radiator assembly.



    E227201
  1. Install the clamp with the screw.



    E227200
  1. Engage the 3 claws and install the heater clamp.



3. INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)


    E174875E02
  1. Using the reference point, install the No. 2 air conditioning radiator damper servo sub-assembly with the 2 screws.
    Text in Illustration 
    *a
    Reference Point



4. INSTALL NO. 1 COOLER THERMISTOR


    E151029E04
  1. Install the No. 1 cooler thermistor as shown in the illustration.
    Part
    Length
    A
    34.3 mm
    1.35 in.
    B
    20.9 mm
    0.82 in.
    C
    50 mm
    1.96 in.
    Text in Illustration 
    *a
    Fixed Part
    *b
    Sensor Part

    NOTICE:
    1. Be sure to insert the thermistor only once because reinserting it into the same position will not allow it to be firmly secured.
    2. When reusing the evaporator, insert the thermistor one row next to the one that has been used previously (X in the illustration).
    3. After inserting the thermistor, do not apply excessive force to the wire.
    4. Directly insert the thermistor until the edge of plastic case "a" comes into contact with evaporator "b".

  1. Engage the 2 clamps.



5. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY


    C129881
  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces. Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

    Compressor oil:
    ND-OIL 8 or equivalent



    E227205
  1. Install the No. 1 cooler evaporator sub-assembly to the blower assembly.



6. INSTALL BLOWER ASSEMBLY WITH COOLER EVAPORATOR SUB-ASSEMBLY
  1. Engage the 2 claws.

  1. Install the blower assembly with cooler evaporator sub-assembly with the 6 screws.

  1. Engage the 3 clamps.



7. INSTALL COOLER EXPANSION VALVE


    E227206
  1. Using a 4 mm hexagon wrench, install the cooler expansion valve with the 2 hexagon bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }



8. INSTALL AIR CONDITIONING HARNESS ASSEMBLY (for Manual Air Conditioning System)


    E227197
  1. Engage the 5 clamps to install air conditioning harness assembly.

  1. Connect the 4 connectors.



    E227196
  1. Install the heater packing as shown in the illustration.



9. INSTALL AIR CONDITIONING HARNESS ASSEMBLY (for Automatic Air Conditioning System)


    E228262
  1. Engage the 5 clamps to install air conditioning harness assembly.

  1. Connect the 5 connectors.



    E227196
  1. Install the heater packing as shown in the illustration.



10. INSTALL ASPIRATOR


    E227232
  1. Engage the 2 claws to install the aspirator.



11. INSTALL COOLER THERMISTOR HOSE (for Automatic Air Conditioning System)


    E234890
  1. Engage the clamp to install the cooler thermistor hose.



12. INSTALL NO. 6 HEATER TO REGISTER DUCT ASSEMBLY


    E227194
  1. Engage the 2 claws and 2 guides to install the No. 6 heater to register duct assembly as shown in the illustration.



13. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY


    E227192
  1. Engage the 2 claws and guide to install the No. 1 air duct sub-assembly as shown in the illustration.