Home › Drivetrain · U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P2769    Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)

DTC    P2770    Open in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)

for Preparation Click here


DESCRIPTION

Shift solenoid valve SL is turned on and off by signals from the ECM to control the hydraulic pressure acting on the lock-up relay valve, which then controls operation of the lock-up clutch.

DTC No.
DTC Detection Condition
Trouble Area
P2769
ECM detects a short in the shift solenoid valve SL circuit when the shift solenoid valve SL is operated (2 trip detection logic).
  1. Short in shift solenoid valve SL circuit
  2. Shift solenoid valve SL
  3. Wiring Harness Connector
  4. ECM
P2770
ECM detects an open in the shift solenoid valve SL circuit when the shift solenoid valve SL is not operated (2 trip detection logic).
  1. Open in shift solenoid valve SL circuit
  2. Shift solenoid valve SL
  3. Wiring Harness Connector
  4. ECM
Fail-safe function:
If the ECM detects a malfunction, it turns shift solenoid valve SL off.

MONITOR DESCRIPTION

Based on the signals from the throttle position sensor, the air flow meter and the crankshaft position sensor, the ECM sends a signal to shift solenoid valve SL to regulate the hydraulic pressure and provide smoother torque converter clutch engagement. Shift solenoid valve SL responds to commands from the ECM. The valve controls the lock-up relay valve to perform the torque-converter lock-up function. If the ECM detects an open or short circuit for shift solenoid valve SL, it will illuminate the MIL.

MONITOR STRATEGY


Related DTCs
P2769: Shift solenoid valve SL/Range check (Low resistance)
P2770: Shift solenoid valve SL/Range check (High resistance)
Required sensors/Components
Shift solenoid valve SL
Frequency of operation
Continuous
Duration
1 time
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


P2769: Range check (Low resistance): 
The monitor will run whenever the following DTCs are not present
None
Solenoid
ON
Time after solenoid OFF to ON
More than 0.008 sec.

P2770: Range check (High resistance): 
The monitor will run whenever the following DTCs are not present
None
Solenoid
ON
Time after solenoid ON to OFF
More than 0.008 sec.

TYPICAL MALFUNCTION THRESHOLDS


P2769: Range check (Low resistance): 
Intelligent power MOS diagnosis fail signals detected while the solenoid is operated
Fail at solenoid resistance: 8 Ω or less

P2770: Range check (High resistance): 
Intelligent power MOS diagnosis fail signals detected while the solenoid is not operated
Fail at solenoid resistance: 100 kΩ or more

COMPONENT OPERATING RANGE


Shift solenoid valve SL
Resistance: 11 to 15 Ω at 20°C (68°F)

WIRING DIAGRAM


C239278E01


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL CIRCUIT)


    C233488E03
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    E26-3 (SL) - Body ground
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
Go to step 2
OK

REPLACE ECM (Click here)  

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
  1. Disconnect the harness connector from the wiring harness connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    E26-3 (SL) - E8-6 (SL)
    Always
    Below 1 Ω
    E26-3 (SL) - Body ground and other terminals
    Always
    10 kΩ or higher
    E8-6 (SL) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)


    C133212E35
  1. Remove the wiring harness connector from the transaxle.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-6 (SL) - Body ground
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 4
OK

REPLACE WIRING HARNESS CONNECTOR (Click here)  

4.INSPECT SHIFT SOLENOID VALVE SL


    C133217E02
  1. Remove shift solenoid valve SL.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Solenoid Connector (SL) - Solenoid Body (SL)
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *1
    Shift Solenoid Valve SL



NG
REPLACE SHIFT SOLENOID VALVE SL (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)