Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System) > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B278841E27

  1. Disconnect the MB, I12 and I13 main body ECU (multiplex network body ECU) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    MB-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    I12-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    ignition switch ACC
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    ignition switch off
    Below 1 V
    MB-31 (ALTB) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    IG power supply
    ignition switch ON
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    IG power supply
    ignition switch off
    Below 1 V
    I13-17 (KSW) - Body ground
    G - Body ground
    Unlock warning switch signal
    No key in ignition key cylinder
    10 kΩ or higher
    I13-17 (KSW) - Body ground
    G - Body ground
    Unlock warning switch signal
    Key in ignition key cylinder
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the MB, I12 and I13 main body ECU (multiplex network body ECU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3C-11 (ACT-) - Body ground
    G - Body ground
    Door lock motor unlock drive output (except driver door)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder off
    Below 1 V
    3C-11 (ACT-) - Body ground
    G - Body ground
    Door lock motor unlock drive output (except driver door)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked
    11 to 14 V
    3C-12 (ACT+) - Body ground
    L - Body ground
    Door lock motor lock drive output (all doors)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder off
    Below 1 V
    3C-12 (ACT+) - Body ground
    L - Body ground
    Door lock motor lock drive output (all doors)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder locked
    11 to 14 V
    3B-4 (ACTD) - Body ground
    GR - Body ground
    Driver door lock motor unlock drive output
    Door control switch (power window regulator master switch assembly) or driver door key cylinder off
    Below 1 V
    3B-4 (ACTD) - Body ground
    GR - Body ground
    Driver door lock motor unlock drive output
    Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked
    11 to 14 V
    3C-15 (FLCY) - Body ground
    L - Body ground
    Front door LH courtesy light switch input
    Front door LH open
    Below 1 V
    3C-15 (FLCY) - Body ground
    L - Body ground
    Front door LH courtesy light switch input
    Front door LH closed
    11 to 14 V
    I13-19 (FRCY) - Body ground
    Y - Body ground
    Front door RH courtesy light switch input
    Front door RH open
    Below 1 V
    I13-19 (FRCY) - Body ground
    Y - Body ground
    Front door RH courtesy light switch input
    Front door RH closed
    11 to 14 V
    I13-1 (LCTY) - Body ground
    P - Body ground
    Rear door LH courtesy light switch input
    Rear door LH open
    Below 1 V
    I13-1 (LCTY) - Body ground
    P - Body ground
    Rear door LH courtesy light switch input
    Rear door LH closed
    Pulse generation
    I13-6 (RCTY) - Body ground
    B - Body ground
    Rear door RH courtesy light switch input
    Rear door RH open
    Below 1 V
    I13-6 (RCTY) - Body ground
    B - Body ground
    Rear door RH courtesy light switch input
    Rear door RH closed
    Pulse generation
    I13-7 (LSFL) - Body ground
    V - Body ground
    Front door LH unlock detection switch input
    Front door LH unlocked
    Below 1 V
    I13-7 (LSFL) - Body ground
    V - Body ground
    Front door LH unlock detection switch input
    Front door LH locked
    Pulse generation
    I13-18 (LSFR) - Body ground
    W - Body ground
    Front door RH unlock detection switch input
    Front door RH unlocked
    Below 1 V
    I13-18 (LSFR) - Body ground
    W - Body ground
    Front door RH unlock detection switch input
    Front door RH locked
    Pulse generation
    2A-53 (LSR) - Body ground
    Y - Body ground
    Rear door RH unlock detection switch input
    Rear door RH unlocked
    Below 1 V
    2A-53 (LSR) - Body ground
    Y - Body ground
    Rear door RH unlock detection switch input
    Rear door RH locked
    Pulse generation
    3C-17 (LSR) - Body ground
    LG - Body ground
    Rear door LH unlock detection switch input
    Rear door LH unlocked
    Below 1 V
    3C-17 (LSR) - Body ground
    LG - Body ground
    Rear door LH unlock detection switch input
    Rear door LH locked
    Pulse generation
    3D-22 (BZR) - Body ground
    BE - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer off
    Below 1 V
    3D-22 (BZR) - Body ground
    BE - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer on
    Pulse generation
    I13-4 (PRG) - Body ground
    P - Body ground
    Signal output to door control receiver
    Key inserted in ignition key cylinder → Key pulled out of ignition key cylinder
    11 to 14 V → Pulse generation → 11 to 14 V
    I13-16 (RDA) - Body ground
    L - Body ground
    Signal input from door control receiver
    Ignition switch off, all doors closed and transmitter switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and transmitter switch pressed
    Pulse generation
    H18-17 (KSW) - Body ground
    G - Body ground
    Key unlock warning switch input
    No key in ignition key cylinder
    11 to 14 V
    Key in ignition key cylinder
    Below 1 V
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.


CHECK DOOR CONTROL RECEIVER (w/ Tire Pressure Warning System)

B280753E03

  1. Disconnect the O25 door control receiver connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O25-7 (+B) - Body ground
    P - Body ground
    Battery (power supply)
    Always
    11 to 14 V
    O25-12 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the O25 door control receiver connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O25-5 (PRG) - O25-12 (GND)
    P - BR
    Signal input from main body ECU (multiplex network body ECU)
    Key inserted in ignition key cylinder → Key pulled out of ignition key cylinder
    11 to 14 V → Pulse generation → 11 to 14 V
    O25-4 (RDA) - O25-12 (GND)
    L - BR
    Signal output to main body ECU (multiplex network body ECU)
    Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch pressed
    Pulse generation

    1. If the result is not as specified, the door control receiver may have a malfunction.


CHECK DOOR CONTROL RECEIVER (w/o Tire Pressure Warning System)

B280754E06

  1. Disconnect the O24 door control receiver connector.

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O24-5 (+B) - Body ground
    W - Body ground
    Battery (power supply)
    Always
    11 to 14 V
    O24-1 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the O24 door control receiver connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O24-3 (PRG) - O24-1 (GND)
    P - BR
    Signal input from main body ECU (multiplex network body ECU)
    Key inserted in ignition key cylinder → Key pulled out of ignition key cylinder
    11 to 14 V → Pulse generation → 11 to 14 V
    O24-2 (RDA) - O24-1 (GND)
    L - BR
    Signal output to main body ECU (multiplex network body ECU)
    Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch not pressed
    11 to 14 V
    Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch pressed
    Pulse generation

    1. If the result is not as specified, the door control receiver may have a malfunction.