Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR

FRONT WIPER MOTOR > INSTALLATION

for Preparation Click here



1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
  1. Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.

  1. Turn the ignition switch to ON (IG).

  1. Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.

  1. Turn the ignition switch off.

  1. Disconnect the connector.



    E226241E01
  1. Apply MP grease to the pivot of the windshield wiper motor assembly.
    Text in Illustration 
    *a
    Pivot of the windshield wiper motor assembly



    E226239E01
  1. Connect the No. 1 rod to the pivot of the windshield wiper motor assembly.
    Text in Illustration 
    *1
    No. 1 Rod
    *a
    Pivot of the windshield wiper motor assembly



2. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E226237E01
  1. Engage the motor grommet as shown in the illustration.
    Text in Illustration 
    *1
    Motor Grommet

    NOTICE:
    Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.

  1. Install the windshield wiper motor and link assembly with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the connector.



3. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 8 guides as shown in the illustration.


    E226235



  1. Engage the 6 claws and guide to install the cowl top ventilator louver sub-assembly.


    E226233



4. INSTALL FRONT FENDER TO COWL SIDE SEAL LH


    E226231
  1. Engage the 3 guides and 2 clips to install the front fender to cowl side seal LH as shown in the illustration.



5. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Use the same procedure as for the LH side.



6. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E226523E01
  1. When reusing the front wiper arm and blade assembly LH:

    1. Clean the wiper arm serrations.
      Text in Illustration 
      *a
      Wiper Arm Serration



    E231343E01
  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.
      Text in Illustration 
      *a
      Wiper Pivot Serration



    E226090E01
  1. Set the front wiper arm and blade assembly LH in the range shown in the illustration and then install the front wiper arm and blade assembly LH with the nut.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    Area
    Measurement
    A
    7.5mm (0.295 in.)
    Text in Illustration 
    *1
    Ceramic Dot

    HINT:
    Hold the wiper arm by hand while tightening the nut.



7. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E226523E01
  1. When reusing the front wiper arm and blade assembly RH:

    1. Clean the wiper arm serrations.
      Text in Illustration 
      *a
      Wiper Arm Serration



    E231343E01
  1. When reusing the windshield wiper link assembly:

    1. Clean the wiper pivot serrations with a wire brush.
      Text in Illustration 
      *a
      Wiper Pivot Serration



    E226089E01
  1. Set the front wiper arm and blade assembly RH in the range shown in the illustration and then install the front wiper arm and blade assembly RH with the nut.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    Area
    Measurement
    A
    7.5mm (0.295 in.)
    Text in Illustration 
    *1
    Ceramic Dot

    HINT:
    Hold the wiper arm by hand while tightening the nut.

  1. Turn the ignition switch to ON (IG).

  1. Operate the front wiper while spraying washer fluid onto the windshield glass. Make sure that the front wiper functions properly and the wiper does not come into contact with the vehicle body.

  1. Lift each wiper arm twice after the wipers stop and check the wiper set position.

  1. Turn the ignition switch off.