Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK

FRONT DOOR LOCK > INSPECTION

for Preparation Click here



1. INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH


    B171377E21
  1. Check the operation of the door lock motor.

    1. Apply battery voltage and check the operation of the door lock motor.

      OK:
      Connection
      Result
      Battery positive (+) → Terminal 4 (L)
      Battery negative (-) → Terminal 1 (UL)
      Locks
      Battery positive (+) → Terminal 1 (UL)
      Battery negative (-) → Terminal 4 (L)
      Unlocks

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock with Motor Assembly LH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock with motor assembly LH.



    B171377E22
  1. Check the operation of the door unlock detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      7 (E) - 8 (LSSR)
      Locked
      10 kΩ or higher
      7 (E) - 8 (LSSR)
      Unlocked
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock with Motor Assembly LH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock with motor assembly LH.



    B273324E01
  1. Check the operation of the door key lock and unlock switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      9 (L) - 7 (E)
      Held to lock side
      Below 1 Ω
      9 (L) - 7 (E)
      Neutral or held to unlock side
      10 kΩ or higher
      10 (UL) - 7 (E)
      Held to unlock side
      Below 1 Ω
      10 (UL) - 7 (E)
      Neutral or held to lock side
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock with Motor Assembly LH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock with motor assembly LH.



2. INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH


    B171378E23
  1. Check the operation of the door lock motor.

    1. Apply battery voltage and check the operation of the door lock motor.

      OK:
      Connection
      Result
      Battery positive (+) → Terminal 4 (L)
      Battery negative (-) → Terminal 1 (UL)
      Locks
      Battery positive (+) → Terminal 1 (UL)
      Battery negative (-) → Terminal 4 (L)
      Unlocks

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock with Motor Assembly RH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock with motor assembly RH.



    B273325E01
  1. Check the operation of the door unlock detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      Locked
      10 kΩ or higher
      7 (LSSR) - 8 (E)
      Unlocked
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock with Motor Assembly RH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock with motor assembly RH.



    B280267E02
  1. Check the operation of the door key lock and unlock switch (w/o Wireless Door Lock Control Function).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      6 (L) - 8 (E)
      Held to lock side
      Below 1 Ω
      6 (L) - 8 (E)
      Neutral or held to unlock side
      10 kΩ or higher
      5 (UL) - 8 (E)
      Held to unlock side
      Below 1 Ω
      5 (UL) - 8 (E)
      Neutral or held to lock side
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (Front Door Lock with Motor Assembly RH)
      *b
      Unlock
      *c
      Lock
      If the result is not as specified, replace the front door lock with motor assembly RH.