Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System) > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B278841E27

  1. Disconnect the MB and I12 main body ECU (multiplex network body ECU) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    I12-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    MB-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Engine switch on (ACC)
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Engine switch off
    Below 1 V
    MB-31 (ALTB) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    IG power supply
    Engine switch on (IG)
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    IG power supply
    Engine switch off
    Below 1 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the MB and I12 main body ECU (multiplex network body ECU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3C-11 (ACT-) - Body ground
    G - Body ground
    Door lock motor unlock drive output (except driver door)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder off
    Below 1 V
    3C-11 (ACT-) - Body ground
    G - Body ground
    Door lock motor unlock drive output (except driver door)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked
    11 to 14 V
    3C-12 (ACT+) - Body ground
    L - Body ground
    Door lock motor lock drive output (all doors)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder off
    Below 1 V
    3C-12 (ACT+) - Body ground
    L - Body ground
    Door lock motor lock drive output (all doors)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder locked
    11 to 14 V
    3B-4 (ACTD) - Body ground
    GR - Body ground
    Driver door lock motor unlock drive output
    Door control switch (power window regulator master switch assembly) or driver door key cylinder off
    Below 1 V
    3B-4 (ACTD) - Body ground
    GR - Body ground
    Driver door lock motor unlock drive output
    Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked
    11 to 14 V
    3C-15 (FLCY) - Body ground
    L - Body ground
    Front door LH courtesy light switch input
    Front door LH open
    Below 1 V
    3C-15 (FLCY) - Body ground
    L - Body ground
    Front door LH courtesy light switch input
    Front door LH closed
    11 to 14 V
    I13-19 (FRCY) - Body ground
    Y - Body ground
    Front door RH courtesy light switch input
    Front door RH open
    Below 1 V
    I13-19 (FRCY) - Body ground
    Y - Body ground
    Front door RH courtesy light switch input
    Front door RH closed
    11 to 14 V
    I13-1 (LCTY) - Body ground
    P - Body ground
    Rear door LH courtesy light switch input
    Rear door LH open
    Below 1 V
    I13-1 (LCTY) - Body ground
    P - Body ground
    Rear door LH courtesy light switch input
    Rear door LH closed
    Pulse generation
    I13-6 (RCTY) - Body ground
    B - Body ground
    Rear door RH courtesy light switch input
    Rear door RH open
    Below 1 V
    I13-6 (RCTY) - Body ground
    B - Body ground
    Rear door RH courtesy light switch input
    Rear door RH closed
    Pulse generation
    I13-7 (LSFL) - Body ground
    V - Body ground
    Front door LH unlock detection switch input
    Front door LH unlocked
    Below 1 V
    I13-7 (LSFL) - Body ground
    V - Body ground
    Front door LH unlock detection switch input
    Front door LH locked
    Pulse generation
    I13-18 (LSFR) - Body ground
    W - Body ground
    Front door RH unlock detection switch input
    Front door RH unlocked
    Below 1 V
    I13-18 (LSFR) - Body ground
    W - Body ground
    Front door RH unlock detection switch input
    Front door RH locked
    Pulse generation
    3A-53 (LSR) - Body ground
    Y - Body ground
    Rear door RH unlock detection switch input
    Rear door RH unlocked
    Below 1 V
    3A-53 (LSR) - Body ground
    Y - Body ground
    Rear door RH unlock detection switch input
    Rear door RH locked
    Pulse generation
    3C-17 (LSR) - Body ground
    LG - Body ground
    Rear door LH unlock detection switch input
    Rear door LH unlocked
    Below 1 V
    3C-17 (LSR) - Body ground
    LG - Body ground
    Rear door LH unlock detection switch input
    Rear door LH locked
    Pulse generation
    3D-22 (BZR) - Body ground
    BE - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer off
    Below 1 V
    3D-22 (BZR) - Body ground
    BE - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer on
    Pulse generation
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B264892E14

  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A43-11 (E) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    A43-2 (+B) - Body ground
    W - Body ground
    Battery power supply
    Always
    11 to 14 V
    A43-10 (CUTB) - Body ground
    L - Body ground
    Dark current cut fuse pin input signal
    Always
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the A43 certification ECU (smart key ECU assembly) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I78-5 (IG) - A43-11 (E)
    LG - W
    IG power supply
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    O1-6 (CSEL) - A43-11 (E)
    LG - W
    Communication channel switching circuit
    Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed → electrical key transmitter sub-assembly switch released
    Below 1 V → 4.5 to 6.0 V → Below 1 V
    O1-17 (RDAM) - A43-11 (E)
    Y - W
    RF Signal input circuit
    Engine switch off
    11 to 14 V pulse generation at regular intervals
    O1-5 (RCO) - A43-11 (E)
    G - W
    Wireless tuner power supply output circuit
    Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed
    Below 1 V → 4.5 to 5.5 V

    1. If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.


CHECK DOOR CONTROL RECEIVER (w/ Daytime Running Light Control)

B280753E02

  1. Disconnect the O25 door control receiver connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O25-7 (+B) - Body ground
    P - Body ground
    Battery (power supply)
    Always
    10 to 16 V
    O25-12 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the Q1 door control receiver connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O25-6 (CSEL) - O25-12 (GND)
    LG - BR
    Smart system receiving channel switching signal input
    Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed → electrical key transmitter sub-assembly switch released
    Below 1 V → 4.5 to 6.0 V → Below 1 V
    O25-9 (DATA) - O25-12 (GND)
    Y - BR
    Smart system recovery code output
    Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed → electrical key transmitter sub-assembly switch released
    Below 1 V → 10 to 16 V → Below 1 V
    O25-10 (+5) - O25-12 (GND)
    G - BR
    Receive mode switching signal input
    Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed
    Below 1 V → 4.5 to 5.5 V

    1. If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.


CHECK DOOR CONTROL RECEIVER (w/o Daytime Running Light Control)

B280754E05

  1. Disconnect the O24 door control receiver connector.

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O24-1 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the O24 door control receiver connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O24-2 (CSEL) - O24-1 (GND)
    LG - BR
    Smart system receiving channel switching signal input
    Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed → electrical key transmitter sub-assembly switch released
    Below 1 V → 4.5 to 6.0 V → Below 1 V
    O24-5 (DATA) - O24-1 (GND)
    Y - BR
    Smart system recovery code output
    Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed → electrical key transmitter sub-assembly switch released
    Below 1 V → 10 to 16 V → Below 1 V
    O24-4 (+5) - O24-1 (GND)
    G - BR
    Receive mode switching signal input
    Engine switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed → electrical key transmitter sub-assembly switch pressed
    Below 1 V → 4.5 to 5.5 V

    1. If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.