Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT

FRONT WHEEL ALIGNMENT > ADJUSTMENT

for Preparation Click here



1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold Tire Inflation Pressure:

    Tire Size
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    P205/65R16 94S
    240 (2.4, 35)
    P215/55R17 93V
    240 (2.4, 35)*1
    210 (2.1, 30)*2
    P225/45R18 91V
    230 (2.3, 33)

    *1: except Mexico
    *2: for Mexico



    C137874
  1. Using a dial indicator, check the runout of the tires.

    Maximum tire runout:
    1.4 mm (0.0551 in.)



2. MEASURE VEHICLE HEIGHT


C239047E01

NOTICE:
  1. Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
  2. Be sure to perform measurement on a level surface.
  3. If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
  4. Inspect while the vehicle is unloaded.
  5. The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  1. Measure the vehicle height.

    Measurement points:
    1. A: Ground clearance of front wheel center
    1. B: Ground clearance of lower No. 2 suspension arm bushing set bolt center
    1. C: Ground clearance of rear wheel center
    1. D: Ground clearance of strut rod set bolt center

    Vehicle Height (Unloaded Vehicle):

    Engine
    Tire Size
    Front A - B
    Rear C - D
    2AR-FE
    205/65R16
    123 mm (4.84 in.)
    52 mm (2.05 in.)
    215/55R17
    122 mm (4.80 in.)*1
    114 mm (4.49 in.)*1, *4
    51 mm (2.01 in.)*1
    44 mm (1.73 in.)*1, *4
    125 mm (4.92 in.)*2
    115 mm (4.53 in.)*2, *4
    54 mm (2.13 in.)*2
    46 mm (1.81 in.)*2, *4
    124 mm (4.88 in.)*3
    52 mm (2.05 in.)*3
    225/45R18
    123 mm (4.84 in.)
    51 mm (2.01 in.)
    2GR-FE
    215/55R17
    127 mm (5.00 in.)
    117 mm (4.61 in.)*4
    57 mm (2.24 in.)
    48 mm (1.89 in.)*4
    225/45R18
    123 mm (4.84 in.)
    54 mm (2.13 in.)

    *1: ASV50L-CETNKA and ASV50L-SETNKA
    *2: ASV50L-CETGKA and ASV50L-SETGKA
    *3: ASV50L-CETSKA
    *4: For Mexico



3. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:
Inspect while the vehicle is unloaded.



    C132440E21
  1. Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.
    Text in Illustration 
    *1
    Turning Radius Gauge
    *2
    Camber-caster-kingpin Gauge

  1. Inspect the camber, caster and steering axis inclination.

    Camber (Unloaded Vehicle):
    Camber Inclination
    Right-left Difference
    -0°40' +/- 45' (-0.67° +/- 0.75°)
    -0°35' +/- 45' (-0.58° +/- 0.75°)*
    45' (0.75°) or less

    * For Mexico

    Caster (Unloaded Vehicle):
    Engine
    Caster Inclination
    Right-left Difference
    2AR-FE
    2°55' +/- 45' (2.92° +/- 0.75°)
    45' (0.75°) or less
    2GR-FE
    3°00' +/- 45' (3.00° +/- 0.75°)
    2°55' +/- 45' (2.92° +/- 0.75°)*

    * For Mexico

    Steering Axis Inclination (Unloaded Vehicle):
    Engine
    Steering Axis Inclination Reference
    2AR-FE
    12°15' (12.25°)
    12°00' (12.00°)*
    2GR-FE
    12°15' (12.25°)
    12°05' (12.08°)*

    * For Mexico



4. ADJUST CAMBER

NOTICE:
Inspect toe-in after the camber has been adjusted.

  1. Remove the front wheel.



    C132409
  1. Remove the 2 nuts on the lower side of the front shock absorber.

    NOTICE:
    Keep the bolts inserted.

  1. Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the shock absorber.

    HINT:
    1. Reinstall each bolt after removing it and confirming steering knuckle movement.
    2. If the steering knuckle does not move freely in the shock absorber, clean the installation surfaces of the front shock absorber and the steering knuckle.

  1. Temporarily install the 2 nuts. (Step A)



    C111319E05
  1. Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)



    C132409
  1. Tighten the nuts.

    Torque:
    290 N*m{ 2957 kgf*cm , 214 ft.*lbf }

    NOTICE:
    Keep the bolts from rotating when tightening the nuts.

  1. Install the front wheel.

    Torque:
    103 N*m{ 1049 kgf*cm , 76 ft.*lbf }



    C239065E01
  1. Check the camber.
    If the measured value is not within the specification, calculate the required adjustment amount using the formula below.
    Camber adjustment amount = center of the specified range - measured value
    Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.

    HINT:
    Try to adjust the camber to the center of the specified values.


    To move the axle hub toward (+) in step B
    To move the axle hub toward (-) in step B
    Refer to table (1) (To move the axle hub toward the positive side)
    Refer to table (2) (To move the axle hub toward the negative side)
    The body and suspension may be damaged if the camber cannot be correctly adjusted according to the tables above.

    NOTICE:
    Replace the nut with a new one when replacing the bolt.




    1. Table (1) (To move the axle hub toward the positive side)


      C212217E01


      Text in Illustration 
      *A
      Table (1) (To move the axle hub toward the positive side)
      *B
      Selected Bolt Combination
      *a
      Installed Bolt
      *b
      Adjusting Value
      *c
      90105-A0052
      *d
      90105-17013
      *e
      90105-17014
      *f
      90105-17015



    2. Table (2) (To move the axle hub toward the negative side)


      C212218E01


      Text in Illustration 
      *A
      Table (2) (To move the axle hub toward the negative side)
      *B
      Selected Bolt Combination
      *a
      Installed Bolt
      *b
      Adjusting Value
      *c
      90105-A0052
      *d
      90105-17013
      *e
      90105-17014
      *f
      90105-17015

  1. If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step (A), replace the existing bolts with the selected bolts.

    HINT:
    Replace one bolt at a time when replacing both bolts.



5. INSPECT TOE-IN

NOTICE:
Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  1. Release the parking brake and move the shift lever to N.

  1. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)



    C188968E05
  1. Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
    Text in Illustration 
    *a
    Tread Center Mark
    *b
    Dimension B
    V100135
    Front of the Vehicle

  1. Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.



    C188969E05
  1. Measure the distance between the tread center marks on the front of the wheels (dimension A).
    Text in Illustration 
    *a
    Dimension A
    V100135
    Front of the Vehicle

    Toe-in (Unloaded Vehicle):
    Specified Condition
    C + D: 0°00' +/- 0°10' (0.00° +/- 0.17°)
    B - A: 0 +/- 2.0 mm (0 +/- 0.0787 in.)

    HINT:
    Measure "B - A" only when "C + D" cannot be measured.

    If the toe-in is not within the specified range, adjust it at the rack ends.



6. ADJUST TOE-IN


    C239071E01
  1. Make sure that the thread length of the right and left rack ends are approximately the same.
    Text in Illustration 
    *a
    Thread Length

    Standard difference:
    1.5 mm (0.0591 in.) or less

  1. Remove the boot clips.



    C239070
  1. Loosen the tie rod end lock nuts.

  1. Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.

    1. If the toe-in measurement is greater than the specified range (too much toe-out), extend the shorter rack end so that the length difference is within the specified range.

    2. If the toe-in measurement is less than the specified range (too much toe-in), shorten the longer rack end so that the length difference is within the specified range.

    3. Measure the toe-in.

  1. Turn the right and left rack ends by an equal amount to adjust the toe-in.

  1. Make sure that the thread lengths of the right and left rack ends are the same.

  1. Tighten the tie rod end lock nuts.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

  1. Place the boots on the seats and install the clips.

    HINT:
    Make sure that the boots are not twisted.



7. INSPECT WHEEL ANGLE


    C132439E11
  1. Put tread center marks on the rearmost points of a turning radius gauge.
    Text in Illustration 
    *a
    Inside
    *b
    Outside
    V100135
    Front of the Vehicle

  1. Turn the steering wheel fully to the left and right and measure the turning angle.

    NOTICE:
    Inspect while the vehicle is unloaded.


    Wheel Turning Angle (Unloaded Vehicle):

    Engine
    Tire Size
    Inside Wheel
    Outside Wheel
    2AR-FE
    205/65R16
    37°15' +/- 2°(37.25° +/- 2°)
    32°50' +/- 2°(32.83° +/- 2°)
    215/55R17
    37°20' +/- 2°(37.33° +/- 2°)*1
    37°35' +/- 2°(37.58° +/- 2°)*1, *4
    32°50' +/- 2°(32.83° +/- 2°)*1
    33°00' +/- 2°(33.00° +/- 2°)*1, *4
    37°15' +/- 2°(37.25° +/- 2°)*2
    37°30' +/- 2°(37.50° +/- 2°)*2, *4
    32°50' +/- 2°(32.83° +/- 2°)*2
    33°00' +/- 2°(33.00° +/- 2°)*2, *4
    37°15' +/- 2°(37.25° +/- 2°)*3
    32°50' +/- 2°(32.83° +/- 2°)*3
    225/45R18
    37°15' +/- 2°(37.25° +/- 2°)
    32°50' +/- 2°(32.83° +/- 2°)
    2GR-FE
    215/55R17
    37°10' +/- 2°(37.17° +/- 2°)
    37°30' +/- 2°(37.50° +/- 2°)*4
    32°50' +/- 2°(32.83° +/- 2°)
    33°00' +/- 2°(33.00° +/- 2°)*4
    225/45R18
    37°20' +/- 2°(37.33° +/- 2°)
    32°50' +/- 2°(32.83° +/- 2°)

    *1: ASV50L-CETNKA and ASV50L-SETNKA
    *2: ASV50L-CETGKA and ASV50L-SETGKA
    *3: ASV50L-CETSKA
    *4: For Mexico
    1. If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.