Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



A247842E22

HINT:
The standard voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated.
The result of checks should be compared with the standard voltage for that pair of terminals, and displayed in the "Specified Condition" column.
The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A25-1 (BATT) - E26-49 (E1)
GR - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
A25-2 (+B) - E26-49 (E1)
P - BR
Power source of ECM
Engine switch on (IG)
11 to 14 V
A25-3 (+B2) - E26-49 (E1)
LG - BR
Power source of ECM
Engine switch on (IG)
11 to 14 V
E26-60 (+BM) - E26-49 (E1)
R - BR
Power source of throttle actuator
Always
11 to 14 V
A25-46 (MREL) - E26-49 (E1)
BE - BR
EFI MAIN relay operation signal
Engine switch on (IG)
11 to 14 V
E26-111 (VCV1) - E26-49 (E1)
LG - BR
Power source for sensors (specific voltage)
Idling with warm engine
4.5 to 5.5 V
A25-32 (IGSW) - E26-49 (E1)
V - BR
Engine switch signal
Engine switch on (IG)
11 to 14 V
A25-51 (STP) - E26-49 (E1)
BE - BR
Stop light switch assembly signal
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
A25-36 (ST1-) - E26-49 (E1)
GR - BR
Stop light switch assembly signal (opposite to STP terminal)
Engine switch on (IG), brake pedal depressed
Below 1.5 V
Engine switch on (IG), brake pedal released
7.5 to 14 V
A25-56 (VCPA) - A25-55 (EPA)
P - Y
Power source of accelerator pedal position sensor (for VPA)
Engine switch on (IG)
4.5 to 5.5 V
A25-59 (VCP2) - A25-58 (EPA2)
L - BE
Power source of accelerator pedal position sensor (for VPA2)
Engine switch on (IG)
4.5 to 5.5 V
A25-54 (VPA) - A25-55 (EPA)
G - Y
Accelerator pedal position sensor signal (for engine control)
Engine switch on (IG), accelerator pedal fully released
0.5 to 1.1 V
Engine switch on (IG), accelerator pedal fully depressed
2.6 to 4.5 V
A25-57 (VPA2) - A25-58 (EPA2)
R - BE
Accelerator pedal position sensor signal (for sensor malfunction detection)
Engine switch on (IG), accelerator pedal fully released
1.2 to 2.0 V
Engine switch on (IG), accelerator pedal fully depressed
3.4 to 5.0 V
E26-126 (VCTA) - E26-125 (ETA)
B - R
Power source for throttle position sensor (specific voltage)
Engine switch on (IG)
4.5 to 5.5 V
E26-128 (VTA1) - E26-125 (ETA)
Y - R
Throttle position sensor signal (for engine control)
Engine switch on (IG), accelerator pedal fully released
0.5 to 1.1 V
Engine switch on (IG), accelerator pedal fully depressed
3.2 to 4.8 V
E26-127 (VTA2) - E26-125 (ETA)
W - R
Throttle position sensor signal (for sensor malfunction detection)
Engine switch on (IG), accelerator pedal fully released
2.1 to 3.1 V
Engine switch on (IG), accelerator pedal fully depressed
4.6 to 5.0 V
A25-7 (VPMP) - E26-49 (E1)
GR - BR
Vent valve
(built into canister pump module)
Engine switch on (IG)
11 to 14 V
A25-6 (MPMP) - E26-49 (E1)
B - BR
Leak detection pump
(built into canister pump module)
Leak detection pump off
Below 3.0 V
Leak detection pump on
9 to 14 V
A25-42 (PPMP) - E26-49 (E1)
B - BR
Canister pressure sensor
(built into canister pump module)
Engine switch on (IG)
3.0 to 3.6 V
A25-45 (TC) - E26-49 (E1)
P - BR
Terminal TC of DLC3
Engine switch on (IG)
11 to 14 V
A25-23 (TACH) - E26-49 (E1)
B - BR
Engine speed signal (for combination meter assembly)
Idling
Pulse generation
(see waveform 1)
A25-10 (SPD) - E26-49 (E1)
L - BR
Vehicle speed signal from combination meter assembly
Driving at 20 km/h (12 mph)
Pulse generation
(see waveform 2)
A25-27 (W) - E26-49 (E1)
LG - BR
Malfunction Indicator Lamp (MIL) operation signal
Engine switch on (IG)
(MIL goes on)
Below 3.0 V
Idling with warm engine
11 to 14 V
E26-58 (#10) - E26-25 (E01)
B - W-B
No. 1 fuel injector assembly signal
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(see waveform 3)
E26-54 (#20) - E26-25 (E01)
R - W-B
No. 2 fuel injector assembly signal
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(see waveform 3)
E26-57 (#30) - E26-25 (E01)
Y - W-B
No. 3 fuel injector assembly signal
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(see waveform 3)
E26-53 (#40) - E26-25 (E01)
L - W-B
No. 4 fuel injector assembly signal
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(see waveform 3)
E26-56 (#50) - E26-25 (E01)
P - W-B
No. 5 fuel injector assembly signal
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(see waveform 3)
E26-55 (#60) - E26-25 (E01)
G - W-B
No. 6 fuel injector assembly signal
Engine switch on (IG)
11 to 14 V
Idling
Pulse generation
(see waveform 3)
A25-9 (STA) - E26-49 (E1)
LG - BR
ST relay operation signal
Cranking
11 to 14 V
E26-35 (OC1+) - E26-5 (OC1-)
W - B
Camshaft timing oil control valve assembly (for intake camshaft of bank 1) operation signal
Idling
Pulse generation
(see waveform 4)
E26-34 (OC2+) - E26-4 (OC2-)
GR - R
Camshaft timing oil control valve assembly (for intake camshaft of bank 2) operation signal
Idling
Pulse generation
(see waveform 4)
E26-33 (OE1+) - E26-3 (OE1-)
L - LG
Camshaft timing oil control valve assembly (for exhaust camshaft of bank 1) operation signal
Idling
Pulse generation
(see waveform 5)
E26-32 (OE2+) - E26-2 (OE2-)
W - Y
Camshaft timing oil control valve assembly (for exhaust camshaft of bank 2) operation signal
Idling
Pulse generation
(see waveform 5)
E26-81 (VV1+) - E26-110 (VV1-)
L - P
VVT sensor (for intake camshaft of bank 1) signal
Idling
Pulse generation
(see waveform 6)
E26-78 (VV2+) - E26-110 (VV1-)
W - P
VVT sensor (for intake camshaft of bank 2) signal
Idling
Pulse generation
(see waveform 6)
E26-79 (EV1+) - E26-110 (VV1-)
V - P
VVT sensor (for exhaust camshaft of bank 1) signal
Idling
Pulse generation
(see waveform 7)
E26-80 (EV2+) - E26-110 (VV1-)
G - P
VVT sensor (for exhaust camshaft of bank 2) signal
Idling
Pulse generation
(see waveform 7)
E26-76 (NE+) - E26-109 (NE-)
G - R
Crankshaft position sensor signal
Idling
Pulse generation
(see waveform 6, 7)
A25-22 (NEO) - E26-49 (E1)
G - BR
Crankshaft position sensor signal sent to certification ECU (smart key ECU assembly)
Idling with warm engine
Pulse generation (see waveform 8)
E26-30 (M+) - E26-59 (ME01)
W - W-B
Throttle actuator operation signal (positive terminal)
Idling with warm engine
Pulse generation
(see waveform 9)
E26-29 (M-) - E26-59 (ME01)
B - W-B
Throttle actuator operation signal (negative terminal)
Idling with warm engine
Pulse generation
(see waveform 10)
E26-107 (IGT1) - E26-49 (E1)
W - BR
No. 1 ignition coil assembly (ignition signal)
Idling
Pulse generation
(see waveform 11)
E26-140 (IGT2) - E26-49 (E1)
G - BR
No. 2 ignition coil assembly (ignition signal)
Idling
Pulse generation
(see waveform 11)
E26-106 (IGT3) - E26-49 (E1)
G - BR
No. 3 ignition coil assembly (ignition signal)
Idling
Pulse generation
(see waveform 11)
E26-139 (IGT4) - E26-49 (E1)
LG - BR
No. 4 ignition coil assembly (ignition signal)
Idling
Pulse generation
(see waveform 11)
E26-105 (IGT5) - E26-49 (E1)
P - BR
No. 5 ignition coil assembly (ignition signal)
Idling
Pulse generation
(see waveform 11)
E26-138 (IGT6) - E26-49 (E1)
L - BR
No. 6 ignition coil assembly (ignition signal)
Idling
Pulse generation
(see waveform 11)
E26-103 (IGF1) - E26-49 (E1)
V - BR
Ignition coil assembly (ignition confirmation signal)
Engine switch on (IG)
4.5 to 5.0 V
Idling
Pulse generation
(see waveform 11)
E26-114 (THW) - E26-117 (ETHW)
B - P
Engine coolant temperature sensor signal
Idling, engine coolant temperature 60 to 120°C (140 to 248°F)
0.2 to 1.0 V
E26-96 (THA) - E26-118 (ETHA)
P - Y
Intake air temperature sensor signal
Idling, intake air temperature 0 to 80°C (32 to 176°F)
0.5 to 3.4 V
E26-46 (AICV) - E26-49 (E1)
L - BR
Vacuum switching valve (for air intake control valve) operation signal
Engine switch on (IG)
11 to 14 V
E26-98 (VG) - E26-130 (E2G)
L - B
Mass air flow meter sub-assembly signal
Idling, shift lever in P or N, A/C switch off
0.5 to 3.0 V
E26-47 (ACIS) - E26-49 (E1)
L - BR
Intake air control valve assembly (for acoustic control induction system) operation signal
Engine switch on (IG)
11 to 14 V
E26-48 (PRG) - E26-49 (E1)
R - BR
Purge VSV for EVAP system operation signal
Engine switch on (IG)
11 to 14 V
Idling with warm engine
Pulse generation
(see waveform 12)
E26-100 (A1A+) - E26-49 (E1)
L - BR
Air fuel ratio sensor (bank 1 sensor 1) signal
Engine switch on (IG)
3.3 V*
E26-132 (A1A-) - E26-49 (E1)
P - BR
Air fuel ratio sensor (bank 1 sensor 1) signal
Engine switch on (IG)
2.9 V*
E26-99 (A2A+) - E26-49 (E1)
R - BR
Air fuel ratio sensor (bank 2 sensor 1) signal
Engine switch on (IG)
3.3 V*
E26-131 (A2A-) - E26-49 (E1)
G - BR
Air fuel ratio sensor (bank 2 sensor 1) signal
Engine switch on (IG)
2.9 V*
E26-26 (HA1A) - E26-21 (E05)
R - W-B
Air fuel ratio sensor (bank 1 sensor 1) heater operation signal
Idling
Pulse generation (see waveform 13)
Engine switch on (IG)
11 to 14 V
E26-20 (HA2A) - E26-21 (E05)
W - W-B
Air fuel ratio sensor (bank 2 sensor 1) heater operation signal
Idling
Pulse generation (see waveform 13)
Engine switch on (IG)
11 to 14 V
E26-101 (OX1B) - E26-102 (EX1B)
W - GR
Heated oxygen sensor (bank 1 sensor 2) signal
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine
Pulse generation
(see waveform 14)
E26-133 (OX2B) - E26-134 (EX2B)
B - R
Heated oxygen sensor (bank 2 sensor 2) signal
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine
Pulse generation
(see waveform 14)
E26-28 (HT1B) - E26-27 (E04)
G - W-B
Heated oxygen sensor (bank 1 sensor 2) heater operation signal
Idling
Below 3.0 V
Engine switch on (IG)
11 to 14 V
E26-22 (HT2B) - E26-27 (E04)
Y - W-B
Heated oxygen sensor (bank 2 sensor 2) heater operation signal
Idling
Below 3.0 V
Engine switch on (IG)
11 to 14 V
A25-8 (ACM) - E26-49 (E1)
R - BR
Duty vacuum switching valve (for active control engine mount system) operation signal
Engine switch on (IG)
11 to 14 V
E26-65 (NSW) - E26-49 (E1)
LG - BR
Park/Neutral position switch assembly signal
Engine switch on (IG) and shift lever in P or N
Below 3.0 V
Engine switch on (IG) and shift lever not in P or N
11 to 14 V
E26-83 (KNK1) - E26-115 (EKNK)
R - G
Knock control sensor (bank 1) signal
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(see waveform 15)
E26-84 (KNK2) - E26-116 (EKN2)
B - W
Knock control sensor (bank 2) signal
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(see waveform 15)
E26-70 (P) - E26-49 (E1)
B - BR
P shift position switch signal
Engine switch on (IG) and shift lever in P
11 to 14 V
Engine switch on (IG) and shift lever not in P
Below 1 V
E26-68 (R) - E26-49 (E1)
GR - BR
R shift position switch signal
Engine switch on (IG) and shift lever in R
11 to 14 V
Engine switch on (IG) and shift lever not in R
Below 1 V
E26-71 (N) - E26-49 (E1)
L - BR
N shift position switch signal
Engine switch on (IG) and shift lever in N
11 to 14 V
Engine switch on (IG) and shift lever not in N
Below 1 V
E26-69 (D) - E26-49 (E1)
G - BR
D shift position switch signal
Engine switch on (IG) and shift lever in D or S
11 to 14 V
Engine switch on (IG) and shift lever not in D or S
Below 1 V
A25-37 (S) - E26-49 (E1)
G - BR
S shift position switch signal
Engine switch on (IG) and shift lever in S
11 to 14 V
Engine switch on (IG) and shift lever not in S
Below 1 V
A25-50 (SFTD) - E26-49 (E1)
V - BR
Down shift switch signal
Engine switch on (IG) and shift lever in S
11 to 14 V
Engine switch on (IG) and shift lever in "-" (down shift) selected
Below 1 V
A25-34 (SFTU) - E26-49 (E1)
R - BR
Up shift switch signal
Engine switch on (IG) and shift lever in S
11 to 14 V
Engine switch on (IG) and shift lever in "+" (up shift) selected
Below 1 V
A25-18 (FPC) - E26-49 (E1)
W - BR
Fuel pump control
Engine stopped, engine switch on (IG)
Below 1.5 V
A25-13 (CANH) - E26-49 (E1)
B - BR
CAN communication line
Engine switch on (IG)
Pulse generation
(see waveform 16)
A25-26 (CANL) - E26-49 (E1)
W - BR
CAN communication line
Engine switch on (IG)
Pulse generation
(see waveform 17)
E26-31 (CAN+) - E26-49 (E1)
B - BR
CAN communication line
Engine switch on (IG)
Pulse generation
(see waveform 16)
E26-1 (CAN-) - E26-49 (E1)
Y - BR
CAN communication line
Engine switch on (IG)
Pulse generation
(see waveform 17)
E26-112 (ALT) - E26-49 (E1)
L - BR
Generator assembly
Engine switch on (IG)
11 to 14 V
A25-5 (RFC) - E26-49 (E1)
G - BR
Cooling fan control
Engine switch on (IG), A/C switch on (max cool)
1.5 to 3.5 V
(average voltage)
E26-108 (GE01) - E26-49 (E1)
G - BR
Shielded earth (ground) circuit of throttle actuator
Always
Below 1 Ω
A25-14 (EC) - Body ground
W-B - -
Ground
Always
Below 1 Ω
E26-49 (E1) - Body ground
BR - -
Ground
Always
Below 1 Ω
E26-25 (E01) - Body ground
W-B - -
Ground
Always
Below 1 Ω
E26-24 (E02) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 Ω
E26-27 (E04) - Body ground
W-B - -
Ground
Always
Below 1 Ω
E26-21 (E05) - Body ground
W-B - -
Ground
Always
Below 1 Ω
*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1
A093225E33
Engine Speed Signal 
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 2
A005135E29
Vehicle Speed Signal 
ECM Terminal Name
Between SPD and E1
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Driving at 20 km/h (12 mph)

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 3
A093279E24
No. 1 (to No. 6) Fuel Injector Assembly Signal 
ECM Terminal Name
Between #10 (to #60) and E01
Tester Range
20 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 4
A093229E11
Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft) Operation Signal 
ECM Terminal Name
Between OC1+ and OC1-, or OC2+ and OC2-
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling

WAVEFORM 5
A093229E11
Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft) Operation Signal 
ECM Terminal Name
Between OE1+ and OE1-, or OE2+ and OE2-
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling

WAVEFORM 6
A207436E01
Crankshaft Position Sensor Signal and VVT Sensor (for Intake Camshaft) Signal 
ECM Terminal Name
Between NE+ and NE-
Between VV1+ and VV1-
Between VV2+ and VV1-
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 7
A207435E01
Crankshaft Position Sensor Signal and VVT Sensor (for Exhaust Camshaft) Signal 
ECM Terminal Name
Between NE+ and NE-
Between EV1+ and VV1-
Between EV2+ and VV1-
Tester Range
5 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 8
A210050E01
Crankshaft Position Sensor Signal 
ECM Terminal Name
Between NEO and E1
Tester Range
5 V/DIV., 2 ms./DIV.
Condition
Idling with warm engine

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 9
A208000E03
Throttle Actuator Positive Terminal Signal 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 10
A245848E01
Throttle Actuator Negative Terminal Signal 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV., 1 ms./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 11
A210049E08
Ignition Coil Assembly Signal (IGT and IGF Signal) 
ECM Terminal Name
Between IGT (1 to 6) and E1
Between IGF1 and E1
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 12
A218020E01
Purge VSV Operation Signal 
ECM Terminal Name
Between PRG and E1
Tester Range
10 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 13
A205412E01
Air Fuel Ratio Sensor (Sensor 1) Heater Operation Signal 
ECM Terminal Name
Between HA1A and E05, or HA2A and E05
Tester Range
5 V/DIV., 10 ms./DIV.
Condition
Idling

HINT:
The wavelength varies in accordance with the engine operating condition.


WAVEFORM 14
A088863E15
Heated Oxygen Sensor (Sensor 2) Signal 
ECM Terminal Name
Between OX1B and EX1B, or OX2B and EX2B
Tester Range
0.2 V/DIV., 200 ms./DIV.
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:
In the Data List, item O2S B1S2 and O2S B2S2 shows the ECM values from the heated oxygen sensor.


WAVEFORM 15
A085286E82
Knock Control Sensor Signal 
ECM Terminal Name
Between KNK1 and EKNK, or KNK2 and EKN2
Tester Range
1 V/DIV., 1 ms./DIV.
Condition
Engine speed maintained at 4000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine speed increases.
  2. The waveforms and amplitudes displayed differ slightly depending on the vehicle condition.


WAVEFORM 16
A086154E48
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANH and E1, or CAN+ and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Engine switch on (IG)

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 17
A086155E44
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANL and E1, or CAN- and E1
Tester Range
1 V/DIV., 10 μs./DIV.
Condition
Engine switch on (IG)

HINT:
The waveform varies depending on the CAN communication signal.