Home › Brake › PARKING BRAKE › PARKING BRAKE PEDAL

PARKING BRAKE PEDAL > REMOVAL

for Preparation Click here



1. REMOVE SHIFT LEVER SUPPORT
  1. for U660E: (Click here)
  2. for U760E: (Click here)


2. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

CAUTION:
When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.

  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B279717
  1. Remove the 4 bolts.

  1. Disengage the 2 claws to disconnect the DLC3.



    B279758
  1. Disengage the 2 hooks to remove the lower No. 1 instrument panel airbag assembly.

    NOTICE:
    When removing the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.



    B279718E01
  1. Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.
    Text in Illustration 
    *1
    Protective Tape
    *2
    Airbag Connector
    *3
    Airbag Connector Lock

  1. Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



3. REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (for Built-in Type Yaw Rate Sensor)
w/ Smart Key System:


4. REMOVE YAW RATE SENSOR (for Separate Type Yaw Rate Sensor)


    C247855
  1. Disconnect the connector from the yaw rate sensor.

  1. Remove the 2 nuts and yaw rate sensor.



5. REMOVE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (for Separate Type Yaw Rate Sensor)
w/ Smart Key System:


6. REMOVE YAW RATE SENSOR BRACKET (for Separate Type Yaw Rate Sensor)


    C247856
  1. Disengage the 2 clamps to separate the wire harnesses.

  1. Remove the 2 bolts and yaw rate sensor bracket.



7. REMOVE FLOOR CARPET BRACKET RH


    E227159
  1. Remove the 2 clips.

  1. Disengage the 2 guides to remove the floor carpet bracket RH.



8. REMOVE AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Turn back the carpet.



    B278814
  1. Disconnect the connectors from the airbag sensor assembly as shown in the illustration.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  1. Remove the 3 bolts and airbag sensor assembly.



9. LOOSEN ADJUSTING NUT


    C237832E01
  1. Remove the lock nut and loosen the adjusting nut.
    Text in Illustration 
    *1
    Lock Nut
    *2
    Adjusting Nut



10. SEPARATE NO. 4 PARKING BRAKE CABLE ASSEMBLY


    C237833E01
  1. Separate the No. 4 parking brake cable assembly from the parking brake control pedal assembly as shown in the illustration.
    Text in Illustration 
    *a
    Turn
    *b
    Hold



11. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY
  1. Turn back the floor carpet.



    C237834
  1. Remove the clip from the No. 1 parking brake cable assembly.

  1. Remove the bolt and 2 nuts, and separate the No. 1 parking brake cable assembly.



    C237835
  1. Disconnect the parking brake switch connector.



    C237836
  1. Remove the bolt, 2 nuts and parking brake control pedal assembly.