DTC P0715 Input / Turbine Speed Sensor Circuit Malfunction |
DTC P0717 Input Speed Sensor Circuit No Signal |

| *1 | Counter Gear | *2 | Clutch Drum |
| *3 | Output Speed Sensor NC | *4 | Input Speed Sensor NT |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0715 | When the speed sensor input voltage is either more than 1.9 V or less than 0.1 V for 4.5 seconds or more.(1-trip detection logic) |
|
| P0717 | ECM detects conditions (a), (b) and (c) continuously for 5 sec. or more: (1-trip detection logic) (a) Vehicle speed: 50 km/h (31 mph) or more (b) Park/neutral position switch (R) is OFF (c) Speed sensor (NT): less than 300 rpm |
| Related DTCs | P0715: Speed sensor (NT)/Range check P0717: Speed sensor (NT)/Verify pulse input |
| Required sensors/Components | Speed sensor (NT), Speed sensor (NC) |
| Frequency of operation | Continuous |
| Duration | P0715: 4.5 sec. P0717: 5 sec. |
| MIL operation | Immediate |
| Sequence of operation | None |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| The monitor will run whenever this DTC is not present. | P0500 (VSS) P0748, P0778, P0798 (Shift solenoid valve (range)) |
| Shift change | Shift change is completed before starting next shift change operation |
| ECM selected gear | 2nd, 3rd, 4th, 5th or 6th |
| Output shaft rpm | 1,000 rpm or more |
| R switch | OFF |
| NSW switch | OFF |
| Engine | Running |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Transmission range switch circuit | Not malfunction |
| Turbine speed sensor range check | Not malfunction |
| Sensor voltage | Less than 0.1 V or more than 1.9 V |
| Sensor signal rpm | Less than 300 rpm |
| Speed sensor (NT) | Turbine speed is equal to engine speed with lock-up ON |

| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| SPD (NT) | Input shaft speed/ Min.: 0 rpm Max.: 12750 rpm | Lock-up is
| Data is displayed in increments of 50 rpm |
| 1.INSPECT TRANSMISSION REVOLUTION SENSOR (SPEED SENSOR INSTALLATION) |
Remove the valve body assembly.
![]() |
Make sure that the connector is properly connected, and check the speed sensor installation (Click here).
|
| ||||
| OK | |
| 2.INSPECT TRANSMISSION WIRE |
![]() |
Disconnect the speed sensor connector from the transmission wire.
Measure the resistance according to the value(s) in the table below.
| Tester Condition | Condition | Specified Condition |
| 1 (NTB) sensor side - A-1 (NTB) wiring harness connector side | Always | Below 1 Ω |
| 2 (NTO) sensor side - A-2 (NTO) wiring harness connector side | Always | Below 1 Ω |
| 1 (NTB) sensor side - Body ground and other terminals | Always | 10 kΩ or higher |
| 2 (NTO) sensor side - Body ground and other terminals | Always | 10 kΩ or higher |
| *a | Component without harness connected (Transmission Wire) |
| *b | Wiring Harness Connector Side |
| *c | Sensor Side |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Condition | Condition | Specified Condition |
| E8-1 (NTB) - E26-116 (NTB) | Always | Below 1 Ω |
| E8-2 (NTO) - E26-115 (NTO) | Always | Below 1 Ω |
| E8-1 (NTB) or E26-116 (NTB) - Body ground and other terminals | Always | 10 kΩ or higher |
| E8-2 (NTO) or E26-115 (NTO) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT WIRING HARNESS CONNECTOR |
Remove the wiring harness connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Condition | Condition | Specified Condition |
| E8-1 (NTB) - A-1 (NTB) | Always | Below 1 Ω |
| E8-2 (NTO) - A-2 (NTO) | Always | Below 1 Ω |
| E8-1 (NTB) - All other terminals | Always | 10 kΩ or higher |
| E8-2 (NTO) - All other terminals | Always | 10 kΩ or higher |
| *a | Component without harness connected (Wiring Harness Connector) |
| *b | ECM Side |
| *c | Transmission Wire Side |
|
| ||||
| OK | |
| 5.REPLACE TRANSMISSION REVOLUTION SENSOR |
| NEXT | |
| 6.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0715 AND/OR P0717 OUTPUT AGAIN) |
Connect the Techstream to the DLC3.
Start the engine and turn the Techstream on.
Clear the DTCs (Click here).
Perform the monitor drive pattern (Click here).
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Display (DTC Output) | Proceed to |
| Only "P0715 or P0717" is output | A |
| No output | B |
|
| ||||
| A | ||
| ||