Home › Drivetrain · U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0715    Input / Turbine Speed Sensor Circuit Malfunction

DTC    P0717    Input Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input revolution (speed) of the transaxle. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (NC), the TCM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, thus, providing smooth gear shifts.

C133216E04


Text in Illustration 
*1
Counter Gear
*2
Clutch Drum
*3
Output Speed Sensor NC
*4
Input Speed Sensor NT

DTC No.
DTC Detection Condition
Trouble Area
P0715
When the speed sensor input voltage is either more than 1.9 V or less than 0.1 V for 4.5 seconds or more.(1-trip detection logic)
  1. Transmission revolution sensor (speed sensor NT)
  2. Transmission wire
  3. TCM
P0717
TCM detects conditions (a), (b) and (c) continuously for 5 sec. or more: (1-trip detection logic)
(a) Vehicle speed: 50 km/h (31 mph) or more
(b) Park/neutral position switch (R) is OFF
(c) Speed sensor (NT): less than 300 rpm

MONITOR DESCRIPTION

The NT terminal of the TCM detects a revolution signal from the speed sensor (NT) (input RPM). The TCM calculates gear shifts comparing the speed sensor (NT) with the speed sensor (NC).
While the vehicle is operating in 2nd, 3rd, 4th or 5th gear with the shift lever in D, if the input shaft revolution (speed) is less than 300 rpm*1 although the output shaft revolution (speed) is more than 1000 rpm*2, the TCM interprets this as a fault, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is 50 km/h (31 mph) or more.

MONITOR STRATEGY


Related DTCs
P0715: Speed sensor (NT)/Range check
P0717: Speed sensor (NT)/Verify pulse input
Required sensors/Components
Speed sensor (NT), Speed sensor (NC)
Frequency of operation
Continuous
Duration
P0715: 4.5 sec.
P0717: 5 sec.
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


P0715: 
Battery voltage
8 V or more
Engine switch
on (IG)
Starter
OFF

P0717: 
The monitor will run whenever this DTC is not present.
P0500 (VSS)
P0748, P0778, P0798 (Shift solenoid valve (range))
Shift change
Shift change is completed before starting next shift change operation
TCM selected gear
2nd, 3rd, 4th, 5th or 6th
Output shaft rpm
1,000 rpm or more
R switch
OFF
NSW switch
OFF
Engine
Running
Battery voltage
8 V or more
Engine switch
on (IG)
Starter
OFF
Transmission range switch circuit
Not malfunction
Turbine speed sensor range check
Not malfunction

TYPICAL MALFUNCTION THRESHOLDS


P0715: 
Sensor voltage
Less than 0.1 V or more than 1.9 V

P0717: 
Sensor signal rpm
Less than 300 rpm

COMPONENT OPERATING RANGE


Speed sensor (NT)
Turbine speed is equal to engine speed with lock-up ON

WIRING DIAGRAM


C133260E23


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the engine switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the engine switch on (IG).
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / ECT / Data List.
  7. According to the display on the Techstream, read the Data List.

    TCM 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    Lock-up is
    1. ON (after warming up engine): Input turbine speed (NT) is equal to engine speed
    2. OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed
    Data is displayed in increments of 50 rpm

    HINT:
    1. SPD (NT) is always 0 while driving: Open or short in the sensor or circuit.
    2. SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

1.INSPECT TRANSMISSION REVOLUTION SENSOR (SPEED SENSOR INSTALLATION)
  1. Remove the valve body assembly.



    C133219
  1. Make sure that the connector is properly connected, and check the speed sensor installation (Click here).

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transaxle case.



NG
REPAIR OR REPLACE TRANSMISSION REVOLUTION SENSOR (Click here)
OK


2.INSPECT TRANSMISSION WIRE


    C189545E15
  1. Remove the TCM.

  1. Disconnect the speed sensor connector from the transmission wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    1 (NTB) sensor side - 1 (NTB) TCM side
    Always
    Below 1 Ω
    2 (NTO) sensor side - 2 (NTO) TCM side
    Always
    Below 1 Ω
    1 (NTB) sensor side - Body ground and other terminals
    Always
    10 kΩ or higher
    2 (NTO) sensor side - Body ground and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)
    *b
    TCM Side
    *c
    Sensor Side



NG
REPLACE TRANSMISSION WIRE (Click here)
OK


3.REPLACE TRANSMISSION REVOLUTION SENSOR
(Click here)

NEXT


4.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0715 AND/OR P0717 OUTPUT AGAIN)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream on.

  1. Clear the DTCs (Click here).

    HINT:
    Write down the currently output DTCs before clearing them.

  1. Perform the monitor drive pattern (Click here).

  1. Enter the following menus: Powertrain / ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.

    Result:

    Display (DTC Output)
    Proceed to
    Only "P0715 or P0717" is output
    A
    No output
    B



B
END
A

REPLACE TCM (Click here)