DTC P0791 Intermediate Shaft Speed Sensor "A" Circuit |
DTC P0793 Intermediate Shaft Speed Sensor "A" |

| *1 | Counter Gear | *2 | Clutch Drum |
| *3 | Output Speed Sensor NC | *4 | Input Speed Sensor NT |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0791 | When the speed sensor input voltage is either more than 1.9 V or less than 0.1 V for 2 seconds or more. (1-trip detection logic) |
|
| P0793 | When the vehicle speed is 25 km/h (15.5 mph) or higher, the counter gear speed is less than 300 rpm for 2 seconds or more. (1-trip detection logic) |
| Related DTCs | P0791: Speed sensor (NC)/Range check P0793: Speed sensor (NC)/Verify pulse input |
| Required sensors/Components | Speed sensor (NT), Speed sensor (NC) |
| Frequency of operation | Continuous |
| Duration | 2 sec. |
| MIL operation | Immediate |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. | P0500 (VSS) P0748, P0778, P0798 (Shift solenoid valve (range)) |
| Vehicle speed | 15.5 mph (25 km/h) or more |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Sensor voltage | Less than 0.1 V or more than 1.9 V |
| Sensor signal rpm | Less than 300 rpm |

| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| SPD (NC) | Counter Gear Speed/ Min.: 0 rpm Max.: 12750 rpm | - | Data is displayed in increments of 50 rpm |
| 1.INSPECT TRANSMISSION REVOLUTION SENSOR (SPEED SENSOR INSTALLATION) |
Remove the valve body assembly.
![]() |
Make sure that the connector is properly connected, and check the speed sensor installation (Click here).
|
| ||||
| OK | |
| 2.INSPECT TRANSMISSION WIRE |
![]() |
Disconnect the speed sensor connector from the transmission wire.
Measure the resistance according to the value(s) in the table below.
| Tester Condition | Condition | Specified Condition |
| 3 (NCO) sensor side - A-3 (NCO) wiring harness connector side | Always | Below 1 Ω |
| 4 (NCB) sensor side - A-4 (NCB) wiring harness connector side | Always | Below 1 Ω |
| 3 (NCO) sensor side - Body ground and other terminals | Always | 10 kΩ or higher |
| 4 (NCB) sensor side - Body ground and other terminals | Always | 10 kΩ or higher |
| *a | Component without harness connected (Transmission Wire) |
| *b | Wiring Harness Connector Side |
| *c | Sensor Side |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Condition | Condition | Specified Condition |
| E26-118 (NCB) - E8-4 (NCB) | Always | Below 1 Ω |
| E26-117 (NCO) - E8-3 (NCO) | Always | Below 1 Ω |
| E26-118 (NCB) or E8-4 (NCB)- Body ground and other terminals | Always | 10 kΩ or higher |
| E26-117 (NCO) or E8-3 (NCO) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT WIRING HARNESS CONNECTOR |
Remove the wiring harness connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Condition | Condition | Specified Condition |
| E8-3 (NCO) - A-3 (NCO) | Always | Below 1 Ω |
| E8-4 (NCB) - A-4 (NCB) | Always | Below 1 Ω |
| E8-3 (NCO) - All other terminals | Always | 10 kΩ or higher |
| E8-4 (NCB) - All other terminals | Always | 10 kΩ or higher |
| *a | Component without harness connected (Transmission Wire) |
| *b | ECM Side |
| *c | Transmission Wire Side |
|
| ||||
| OK | |
| 5.REPLACE TRANSMISSION REVOLUTION SENSOR |
| NEXT | |
| 6.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0791 AND/OR P0793 IS OUTPUT AGAIN) |
Connect the Techstream to the DLC3.
Start the engine and turn the Techstream on.
Clear the DTCs (Click here).
Perform the monitor drive pattern (Click here).
Enter the following menus: / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Display (DTC Output) | Proceed to |
| Only "P0791 or P0793" is output | A |
| No output | B |
|
| ||||
| A | ||
| ||