Home › Drivetrain · U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0989    Transmission Fluid Pressure Sensor / Switch "E" Circuit Low

DTC    P0990    Transmission Fluid Pressure Sensor / Switch "E" Circuit High

for Preparation Click here


DESCRIPTION

ATF pressure switch No. 3 is installed in the lock-up solenoid ATF output passage and is used to detect a malfunction in the lock-up solenoid.

DTC No.
DTC Detection Condition
Trouble Area
P0989
Transmission fluid pressure switch No. 3 is OFF when lock-up occurs in response to a lock-up request (2 trip detection logic).
  1. ATF temperature sensor assembly (ATF pressure switch No. 3)
  2. Transmission wire
  3. TCM
P0990
When both of the following are detected (2 trip detection logic):
  1. Transmission fluid pressure switch No. 3 is ON when lock-up does not occur.
  2. Lock-up does not occur when shift solenoid valve (SLU) is requested to turn off in the lock-up range.

MONITOR DESCRIPTION

The TCM illuminates the MIL and stores the DTC when the TCM detects that the ATF pressure switch is OFF with the lock-up solenoid ON or when the TCM detects that the ATF pressure switch is ON with the lock-up solenoid OFF.

MONITOR STRATEGY


Related DTCs
P0989: Transmission fluid pressure switch No. 3 OFF malfunction
P0990: Transmission fluid pressure switch No. 3 ON malfunction
Required sensors/Components
Transmission fluid pressure switch No. 3
Frequency of operation
Continuous
Duration
P0989: 1.8 sec.
P0990 (a): 1.2 sec.
P0990 (b): 0.6 sec.
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


ALL: 
The monitor will run whenever this DTC is not present.
(Not circuit malfunction)
P0712, P0713 (ATF temperature sensor circuit (TFT sensor))
P0115, P0117, P0118 (ECT sensor circuit)
P0715, P0717 (Turbine speed sensor circuit)
P0791, P0793 (Intermediate shaft speed sensor circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P0798 (Shift solenoid valve SL3 circuit)
P2810 (Shift solenoid valve SL4 circuit)
P2759 (Shift solenoid valve SLU circuit)
P2769, P2770 (Shift solenoid valve SL circuit)
P0327, P0328, P0332, P0333 (KCS sensor circuit)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P1607, P2102, P2103, P2111, P2112, P2118, P2119, P2135 ((ETCS) Electronic throttle control system)
U0100 (CAN communication system)
ECT (Engine coolant temperature)
40°C (104°F) or more
Spark advance from Max. retard timing by KCS control
0°CA or more
Transmission range
"D"
TFT (Transmission fluid temperature)
-10°C (14°F) or more
TFT (Transmission fluid temperature) sensor circuit
No circuit malfunction
ECT (Engine coolant temperature) sensor circuit
No circuit malfunction
Turbine speed sensor circuit
No circuit malfunction
Intermediate shaft speed sensor circuit
No circuit malfunction
Shift solenoid valve SL1 circuit
No circuit malfunction
Shift solenoid valve SL2 circuit
No circuit malfunction
Shift solenoid valve SL3 circuit
No circuit malfunction
Shift solenoid valve SL4 circuit
No circuit malfunction
Shift solenoid valve SLU circuit
No circuit malfunction
Shift solenoid valve SL circuit
No circuit malfunction
(KCS) Knock control sensor circuit
No circuit malfunction
(ETCS) Electronic throttle control system
Not system down
CAN communication system
Not system down
Engine
Starting
TCM selected gear
Not 1st
Vehicle speed
15.5 mph (25 km/h) or more
Turbine speed/Output speed (NT/NO) with 1st
3.304 to 7.724
Turbine speed/Output speed (NT/NO) with 2nd
1.901 to 2.340
Turbine speed/Output speed (NT/NO) with 3rd
1.399 to 1.649
Turbine speed/Output speed (NT/NO) with 4th
0.998 to 1.138
Turbine speed/Output speed (NT/NO) with 5th
0.705 to 0.836
Turbine speed/Output speed (NT/NO) with 6th
0.568 to 0.695

P0989: 
TCM lock-up command
ON
Engine speed - Turbine speed
Less than 35 rpm
Throttle valve opening angle
7% or more
Vehicle speed
Less than 62.1 mph (100 km/h)
Shift solenoid valve SLU
Not ON malfunction

P0990: 
TCM indicated pressure valve of SLU
Less than 4 kPa
TCM lock-up command
OFF
Shift solenoid valve SLU
Not malfunction
Shift solenoid valve SL
Not OFF malfunction

TYPICAL MALFUNCTION THRESHOLDS


P0989: 
Transmission fluid pressure switch No. 3
OFF

P0990: 
Following conditions are met
(a) and (b)
(a) Engine speed - Turbine speed
35 rpm or more
(b) Transmission fluid pressure switch No. 3
ON

WIRING DIAGRAM


C133258E28


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0989 OR P0990)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.

    Result:

    Display (DTC Output)
    Proceed to
    Only "P0990" is output
    A
    Only "P0989" is output
    B
    "P0989 or P0990" and other DTCs are output
    C

    HINT:
    If a solenoid is stuck OFF, DTCs for several solenoids including the malfunctioning solenoid will be detected.



B
Go to step 4

C
GO TO DTC CHART (Click here)
A


2.CHECK TRANSMISSION WIRE (SHORT TO GROUND)


    C133212E57
  1. Remove the TCM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    19 (TPS3) - Body ground (Valve body assembly) and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 3
OK

REPLACE TCM (Click here)  

3.CHECK ATF TEMPERATURE SENSOR ASSEMBLY (ATF PRESSURE SWITCH NO. 3)
  1. Remove the oil strainer assembly.



    C142709E01
  1. Disconnect the connector from the ATF temperature sensor assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    1 (TPS3) - Body ground (Valve body assembly) and other terminals
    Always
    10 kΩ or higher



NG
REPLACE ATF TEMPERATURE SENSOR ASSEMBLY (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)  

4.CHECK TRANSMISSION WIRE
  1. Remove the oil strainer assembly.



    C175651E17
  1. Remove the TCM.

  1. Disconnect the connector from the ATF temperature sensor assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    19 (TPS3) TCM side - 1 (TPS3) sensor side
    Always
    Below 1 Ω
    1 (TPS3) sensor side - Body ground (Valve body assembly) and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire))
    *b
    TCM Side
    *c
    ATF Temperature Sensor Side



NG
REPLACE TRANSMISSION WIRE (Click here)
OK


5.REPLACE ATF TEMPERATURE SENSOR ASSEMBLY
(Click here)

NEXT


6.CHECK IF DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream on.

  1. Clear the DTCs (Click here).

    HINT:
    Write down the currently output DTCs before clearing them.

  1. Perform the monitor drive pattern (Click here).

  1. Enter the following menus: Powertrain / ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.

    Result:

    Display (DTC Output)
    Proceed to
    Only "P0989" is output
    A
    No output
    B



B
END
A

REPLACE TCM (Click here)