Home › Drivetrain · U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P2810    Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4)

for Preparation Click here


DESCRIPTION

Changing from 1st to 6th is performed by the ECM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated (Click here)

DTC No.
DTC Detection Condition
Trouble Area
P2810
The ECM checks for an open or short in the shift solenoid valve SL4 circuit while driving and shifting gears. (1-trip detection logic)
  1. Output signal duty equals to 100%.
    (NOTE: SL4 output signal duty is less than 100% under normal condition.)
  1. Open or short in shift solenoid valve SL4 circuit
  2. Shift solenoid valve SL4
  3. Wiring Harness Connector
  4. ECM

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL and stores the DTC. And the ECM performs the fail-safe function and turns the other normal shift solenoid valves on or off (In case of an open or short circuit, the ECM stops sending current to the circuit.)
(Click here).

MONITOR STRATEGY


Related DTCs
P2810: Shift solenoid valve SL4/Range check
Required sensors/Components
Shift solenoid valve SL4
Frequency of operation
Continuous
Duration
1 sec.
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
None
Ignition switch
ON
Starter
OFF

Condition (A) 
Battery voltage
12 V or more

Condition (B) 
Battery voltage
10 V or more and less than 12 V
Target current
Less than 0.75 A

Condition (C) 
Battery voltage
8 V or more
Target current
0.6 A or more

TYPICAL MALFUNCTION THRESHOLDS

When one of the following conditions is met: Condition (A), (B) or (C)

Condition (A) and (B) 
Output duty cycle
100% or more

Condition (C) 
Output duty cycle
0% or less

COMPONENT OPERATING RANGE


Output duty cycle
More than 3% and less than 100%

WIRING DIAGRAM


C239277E03


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL4 CIRCUIT)


    C233488E04
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    E26-9 (SL4+) - E26-8 (SL4-)
    20°C (68°F)
    5.0 to 5.6 Ω
    E26-9 (SL4+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E26-8 (SL4-) - Body ground and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
Go to step 2
OK

REPLACE ECM (Click here)  

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
  1. Disconnect the harness connector from the wiring harness connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Condition
    Specified Condition
    E26-9 (SL4+) - E8-21 (SL4+)
    Always
    Below 1 Ω
    E26-8 (SL4-) - E8-20 (SL4-)
    Always
    Below 1 Ω
    E26-9 (SL4+) or E8-21 (SL4+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E26-8 (SL4-) or E8-20 (SL4-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT TRANSMISSION WIRE (SL4)


    C133212E33
  1. Remove the wiring harness connector from the automatic transaxle.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-22 (SL4+) - A-21 (SL4-)
    20°C (68°F)
    5.0 to 5.6 Ω
    A-22 (SL4+) - Body ground and other terminals
    Always
    10 kΩ or higher
    A-21 (SL4-) - Body ground and other terminals
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 4
OK

REPLACE WIRING HARNESS CONNECTOR (Click here)  

4.INSPECT SHIFT SOLENOID VALVE SL4


    C201747E01
  1. Remove shift solenoid valve SL4.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

    OK:
    Valve moves and makes an operating sound.

    Text in Illustration 
    *1
    Shift Solenoid Valve SL4



NG
REPLACE SHIFT SOLENOID VALVE SL4 (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)